Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 30, Problem 13RQ
What is the principal cause of tool wear in ECM?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What is tool coating?
Identify the following function of tools. Write whether it is under Electro-Static Discharge (ESD) tools, Hand Tools, or Diagnostic Tools.
define the "activity" in RPA tools
Chapter 30 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 30 - How do the MRRs for most NTM processes compare to...Ch. 30 - What are the steps in chemical machining using...Ch. 30 - In chemical machining, should the etchant be...Ch. 30 - What are the advantages of chemical blanking over...Ch. 30 - How are multiple depths of cut (steps) produced by...Ch. 30 - Would it be feasible to produce a groove 2 mm wide...Ch. 30 - A drawing calls for making a groove 23 mm wide and...Ch. 30 - Could an ordinary steel weldment be chemically...Ch. 30 - How could you produce a tapered section by...Ch. 30 - What is the principal application of...
Ch. 30 - How is ECM related to chemical machining?Ch. 30 - What effect does work material hardness have on...Ch. 30 - What is the principal cause of tool wear in ECM?Ch. 30 - Would electrochemical grinding be a suitable...Ch. 30 - Upon what factors does the metal removal rate...Ch. 30 - Why is the tool insulated in the ECM schematic?Ch. 30 - What is the nature of the surface obtained by...Ch. 30 - What is the principal advantage of using a moving...Ch. 30 - What effect would increasing the voltage have on...Ch. 30 - If a metal part is quite brittle and the part will...Ch. 30 - If you had to make several holes in a large number...Ch. 30 - Prob. 22RQCh. 30 - Explain (using a little physics and metallurgy)...Ch. 30 - Prob. 24RQCh. 30 - What are some possible defects that can result...Ch. 30 - What are some other uses for the laser other than...Ch. 30 - How does the laser produce coherent light...Ch. 30 - What is ablation?Ch. 30 - What is an excimer?Ch. 30 - In Figure 30.16, what is the protective tape...Ch. 30 - Why is the EBM process done in a vacuum?Ch. 30 - What is the major problem with the redesigned cap...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Determine the normal stress in each member of the truss structure. All joints are ball joint, and the material ...
Introduction To Finite Element Analysis And Design
Assume that the air in Problem 3-22 is supplied to the space at 53 F (12 C). Compute the volume flow rate of th...
Heating Ventilating and Air Conditioning: Analysis and Design
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
9.17 Compute the total elongation of a steel bar, originally 25 in. long, if the induced tensile stress is 15,0...
Applied Statics and Strength of Materials (6th Edition)
Determine the force in members BC, CF, and FE and state if the members are in tension or compression. Prob. F5-...
Statics and Mechanics of Materials (5th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Multiple grooving is most suited for: a/Rough grooving when the depth is bigger than the width b/Minimizing vibrations and radial forces c/ Machining steel and stainless steel and when the width of the groove is larger than the deptharrow_forwardMain characteristic when cutting Non-ferrous materials ISO N is: O Machining at higher speeds creates abrasive wear Non-ferrous materials are sticky and need sharp cutting edges Machining creates high cutting forces, built-up edge, heat and deformation hardeningarrow_forwardWhat are the two types of EDM machines?arrow_forward
- I need the answer as soon as possiblearrow_forwardPlease describe briefly in MS word urgentarrow_forwardMain characteristic when cutting Stainless Steel ISO M is: a/ Machining creates high cutting forces, built-up edge, heat and deformation hardening b/ Short-chipping material c/ Stainless steel is sticky and needs sharp cutting edgesarrow_forward
- Explain what may occur that makes it necessary to enter a wear offset for a particular tool.arrow_forwardWhen machining workpieces made from bar stock, what are two automated devices used to advance the bar so that the next workpiece can be machined?arrow_forward3. What makes EDM become a key in tool and die making machine tool ? 3arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License