FEA Problem 1•Assemble the element equations to obtain the force-displacement relations for the entire system.Use the boundary conditions to write the condensed equations for the unknown displacements andforces.k2 = 80 lb/in.k5k = 120 lb/in.ww100 lbww80 lbk6kg = 180 lb/in.k₁ = 60 lb/ik3 = 50 lb/in.www==k₁ = 150 lb/in.

Answered: Image /qna-images/answer/964b39a9-e455-43b2-a7eb-4a322e3e666f.jpg

Answered: Problem 1 • Assemble the element…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.10P: Solve the preceding problem for the following data: x=190106,y=230106,xy=160106,and=45.

See similar textbooks

Similar questions

A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance measured along the beam; [x]=[L] y = displacement of the beam; [y]=[L] = circular frequency of vibration; []=[T1] = mass of the beam per unit length; []=[ML1] D = bending rigidity of beam; [D]=[FL2] Show that the equation is dimensionally homogeneous. Note that [F]=[MLT2] see Eq. (1.21:).
The drag on an airplane wing in flight is known to be a function of the density of air (), the viscosity of air(), the free-stream velocity (U), a characteristic dimension of the wing (s), and the shear stress on the surface of the wing (s). Show that the dimensionless drag, sU2, can be expressed as a function of the Reynolds number, Us.
A differential equation is d2ydt2=Ay2+Byt where y represents a distance and t is time. Determine the dimensions of constants A and B for which the equation will be dimensionally homogeneous.
Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
5.2 Evaluate the Prandtl number from the following data: , .
Repeat Problem 6.2-17 but now use a transformed-section approach.
Solve the preceding problem for the following data:P = 160 kN,JV = 200 tN,L = 2 m,b = 95 mm, h = 300 mm, and d = 200 mm
Using the information in Problem 1.22, estimate the ambient air temperature that could cause frostbite on a calm day on the ski slopes. 1.22 In order to prevent frostbite to skiers on chair lifts, the weather report at most ski areas gives both an air temperature and the wind-chill temperature. The air temperature is measured with a thermometer that is not affected by the wind. However, the rate of heat loss from the skier increases with wind velocity, and the wind-chill temperature is the temperature that would result in the same rate of heat loss in still air as occurs at the measured air temperature with the existing wind. Suppose that the inner temperature of a 3-mm-thick layer of skin with a thermal conductivity of 0.35W/mKis35C and the air temperature is 20C. Under calm ambient conditions the heat transfer coefficient at the outer skin surface is about 20W/m2K (see Table 1.4), but in a 40-mph wind it increases to 75W/m2K. If frostbite occurs when the skin temperature drops to about 10C, do you advise the skier to wear a face mask? What is the skin temperature drop due to the wind?
5.19 Suppose that the graph below shows measured values of for air in forced convection over a cylinder of diameter D. plotted on a logarithmic graph of as a function of ReD Pr. Write an appropriate dimensionless correlation for the average Nusselt number for these data and state any limitations to your equation.
Solve the preceding problem for the element shown in the figure.
-4-13 A propped cantilever beam of a length 2L is loaded by a uniformly distributed load with intensity q. The beam is supported at B by a linearly elastic spring with stiffness k. Use the method of superposition to solve for all reactions. Also draw shear-force and bending-moment diagrams, labeling all critical ordinates. Let k = 6EI/L3.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

Refrigeration and Air Conditioning Technology (Mi…

Mechanical Engineering

ISBN:

9781305578296

Author:

John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:

Cengage Learning

Automotive Technology: A Systems Approach (MindTa…

Mechanical Engineering

ISBN:

9781133612315

Author:

Jack Erjavec, Rob Thompson

Publisher:

Cengage Learning

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

SEE MORE TEXTBOOKS