A cylindrical tank is folly filled with water (Fig. P3-67). In order to increase the flow from the tank, an additional pressure is applied to the water surface by a compressor. For
The hydrostatic force on the surface (A) exerted by water.
Answer to Problem 67P
The hydrostatic force on the surface (A) exerted by water for air pressure
The hydrostatic force on the surface (A) exerted by water for air pressure
The hydrostatic force on the surface (A) exerted by water for air pressure
Explanation of Solution
Given information:
The pressure applied to the water by compressor are
Write the expression for the pressure exerted by the fluid.
Density of the fluid is
Substitute
Here, diameter of the pipe is
Write the expression for total pressure exerted on the surface.
Here, air pressure is
Substitute
Write the expression for the area of the surface
Here the diameter of the pipe is
Write the expression for the force acting on the surface
Substitute
Calculation:
For air pressure
Substitute
Substitute
For air pressure
Substitute
Substitute
For air pressure
Substitute
Substitute
Conclusion:
The hydrostatic force on the surface (A) exerted by water for air pressure
The hydrostatic force on the surface (A) exerted by water for air pressure
The hydrostatic force on the surface (A) exerted by water for air pressure
Want to see more full solutions like this?
Chapter 3 Solutions
Fluid Mechanics: Fundamentals and Applications
- 2. There is a liquid having density of Np below a liquid of density p (N is an unknown constant). A piston of a rectangular cross section (width H into the page) is attached to a completely submerged sphere of density e/3 and volume 4/2H3, with a pulley attachment as shown in the figure. The piston surface has a 45° angle with respect to the horizontal direction and a 90° angle with the pulley cable. It is measured that the within the piston is atmospheric. pressure (a) Identify all the forces applied to the piston surface, and mark them on a free body diagram. Accurately indicate their points of action. (b) Evaluate N if all the forces applied to the piston surface balance. Air P/3 2H g Piston surface Np Harrow_forwardA cylindrical tank is fully filled with water (Fig. P3–67).In order to increase the flow from the tank, an additionalpressure is applied to the water surface by a compressor. ForP0 = 0, P0 = 5 bar, and P0 = 10 bar, calculate the hydrostaticforce on the surface A exerted by water.arrow_forward(a) Explain howv could you determine the resultant force on a curved surface inmrnersed in a liquid? (b) A curve gate AB is defined by y = x' and 2 m wide as shown in Figure Q1 is hinged at bottom A. Determine the minimum force (Fo) required to hold the gate closed. Concrete wall- Water, SG = 1.00 1 m FB B 2 m ソミ×? Hinge A 0.5 m Figure Q1arrow_forward
- Q3) Find the horizantal and vertical pressure force exerted on the gate (AB) of the tank. I [Tank length = 3.5 m). P=15kq Water r=2marrow_forwardIn the water, a square plate with (side= a) is lying vertically, with its upper horizontal edge touching the water's surface. The positions of the centre of pressure (h*) on the planar surface and the total pressure force (P) will be determined by: [Where, p is the density of water (a) P=pga/2, h=2/3.a (b) P=pga¹/2, h=2/5.a (c) P pga/4, h-2/5.a (d) P=pga/3, h=2/3.a (e) P=pga¹/5, h=2/7.aarrow_forwardBottle was filled with water and a hole is punched in the bottle.When the bottle is closed, water does not come out of the hole. However, when the bottle is open, water comes out of the hole. Other information would be - Atmospheric pressure is 1 atm (101325 Pa) - Assume bottle is 20 cm and the hole is on the 10 cm above the bottom of the bottle (use it as reference level) Define the pressure(s) acting at the hole when the bottle is open and calculate total pressure. Define the pressure(s) acting at the hole when the bottle is closed and calculate total pressure. Using the results from part a and b, why does water come out when the bottle is open and why does not it come out when the bottle is closed?arrow_forward
- I need the answer as soon as possiblearrow_forwardplease draw ah fbd so I can understand it better. Thankyou!arrow_forwardA closed cylindrical vessel, 2m in diameter & 4m high is fully filled with water & rotated to its vertical axis at a constant speed of 12.2 rad/sec. The top is pressurized by 180 KPa. (a) What is the pressure at the center bottom of the cylinder? (b) What is the pressure at the circumference bottom of the cylinder? (c) What is the total hydrostatic force at the sides of the cylinder?arrow_forward
- i need the answer quicklyarrow_forward2. The gage pressure of the air in the Oil tank is measured to be 65 kPa. Find SG = 0.72 the differential height (h) of the 75 cm column. Specific gravities (SG) of Air -Water the manometer fluids are given in 30 cm -Mercury SG = 13.6 h the figure. Assume that the density of water is 1000 kg/m³.arrow_forwardB2arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY