Three single-phase two-winding transformers, each rated 25 MVA , 34 . 5 / 13 . 8 kV , are connected to form a three-phase Δ − Δ bank. Balanced positive-suence voltages are applied to the high-voltage terminals, and a balanced, resistive Y load connected to the low-voltage terminals absorbs 75 MW at 13.8 kV. If one of the single-phase transformers is removed (resulting in an open − Δ connection) and the balanced load is simultaneously reduced to 43.3 MW ( 57 . 7 % of the original value), determine (a) the load voltages V a η , V b η , and V c η ; (b) load currents I a , I b , and I c ; and (c) the MVA supplied by each of the remaining two transformers. Are balanced voltages still applied to the load? Is the open − Δ transformer overloaded?
Three single-phase two-winding transformers, each rated 25 MVA , 34 . 5 / 13 . 8 kV , are connected to form a three-phase Δ − Δ bank. Balanced positive-suence voltages are applied to the high-voltage terminals, and a balanced, resistive Y load connected to the low-voltage terminals absorbs 75 MW at 13.8 kV. If one of the single-phase transformers is removed (resulting in an open − Δ connection) and the balanced load is simultaneously reduced to 43.3 MW ( 57 . 7 % of the original value), determine (a) the load voltages V a η , V b η , and V c η ; (b) load currents I a , I b , and I c ; and (c) the MVA supplied by each of the remaining two transformers. Are balanced voltages still applied to the load? Is the open − Δ transformer overloaded?
Solution Summary: The author calculates the line-to-line voltage rating for every single-phase transformer.
Three single-phase two-winding transformers, each rated
25 MVA
,
34
.
5
/
13
.
8
kV
, are connected to form a three-phase
Δ
−
Δ
bank. Balanced positive-suence voltages are applied to the high-voltage terminals, and a balanced, resistive Y load connected to the low-voltage terminals absorbs 75 MW at 13.8 kV. If one of the single-phase transformers is removed (resulting in an open
−
Δ
connection) and the balanced load is simultaneously reduced to 43.3 MW (
57
.
7
%
of the original value), determine (a) the load voltages
V
a
η
,
V
b
η
,
and
V
c
η
;
(b) load currents
I
a
,
I
b
,
and
I
c
;
and (c) the MVA supplied by each of the remaining two transformers. Are balanced voltages still applied to the load? Is the open
−
Δ
transformer overloaded?
You just got a job at Shin-Etsu Chemical growing Si crystals with different dopants. Howmuch Ga needs to be added to 800 kg of Si melt to achieve a 5-10 Ω.cm (measured at midheight) Si CZ crystal with the following characteristics: height: 7 ft, width: 12 inchesdiameter. Assume, angular rotation 10 RPM, melt viscosity 0.1 poise, pull velocity 2mm/min.a. Generate a plot of the doping distribution throughout the length of the crystal (CGa vs. fs ).b. If a second crystal were to be pulled out of the melt without replenishment of silicon nordopant what would be the average resistivity of this crystal (or resistivity at mid height)
DO NOT USE AI OR CHAT GPT NEED HANDWRITTEN SOLUTION
Chapter 3 Solutions
MindTap Engineering for Glover/Overbye/Sarma's Power System Analysis and Design, 6th Edition, [Instant Access], 1 term (6 months)
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.
How does a Transformer work - Working Principle electrical engineering; Author: The Engineering Mindset;https://www.youtube.com/watch?v=UchitHGF4n8;License: Standard Youtube License