Fluid Mechanics Fundamentals And Applications
3rd Edition
ISBN: 9780073380322
Author: Yunus Cengel, John Cimbala
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 3, Problem 123P
Milk with a density of 1020 kg/m3 is transported on a level road in a 9-m-long, 3-m-diameter cylindrical tanker. The tanker is completely filled with milk (no air space), and it accelerates at 4 m/s2. If the minimum pressure in the tanker is 100 kPa, determine the maximum pressure difference and the location of the maximum pressure.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Milk with a density of 970 kg/m^3 is transported on a level road in a 9-m long, 3-m diameter cylindrical
tanker. The tanker is completely filled with milk, i.e., no air space in the tank. If the truck is accelerating
from a stop signal at 7.0 m/s^2 to the left, determine the pressure difference between the maximum
and minimum pressures in the tank. Depict on the figure the location of the minimum and maximum
pressures in the tank.
min.
9m
3m
Determine the difference between the total pressure of an aircraft flying at sea level, and an aircraft flying at 5KM? Both have a velocity of 100m/s.
A 3-m-diameter, 7-m-long cylindrical tank is completely filled with water. The tank is pulled by a truck on a level road with the 7-m-long axis being horizontal. Determine the pressure difference between the front and back ends of the tank along a horizontal line when the truck (a) accelerates at 3 m/s2 and (b) decelerates at 4 m/s2.
Chapter 3 Solutions
Fluid Mechanics Fundamentals And Applications
Ch. 3 - Someone claims that the absolute pressure in a...Ch. 3 - A tinysteel cube is suspended in water by a...Ch. 3 - Express Pascal’s law, and give a real-world...Ch. 3 - Consider two identical fans, one at sea level and...Ch. 3 - What is the difference between gage pressure and...Ch. 3 - Explain why some people experience nose bleeding...Ch. 3 - Prob. 7PCh. 3 - A vacuum gage connected to a chamber reads 36 kPa...Ch. 3 - The pressure at the exit of an air compressor is...Ch. 3 - The pressure in a water line is 1500 kPa. What is...
Ch. 3 - A manometer is used to measure the air pressure in...Ch. 3 - The water in a tank is pressurized by air, and the...Ch. 3 - Determine the atmospheric pressure at a location...Ch. 3 - The gagepressure in a liquid at a depth of 2.5 m...Ch. 3 - The absolute pressure in water at a depth of 8 m...Ch. 3 - Show that 1kgf/cm2=14.223psi .Ch. 3 - Prob. 17EPCh. 3 - Consider a 55-kg woman who has a total foot...Ch. 3 - A vacuum gage connected to a tank reads 45 kPa at...Ch. 3 - Prob. 20EPCh. 3 - A pressure gage connected to a tank reads 500kPa...Ch. 3 - Prob. 22PCh. 3 - Prob. 23PCh. 3 - Water from a reservoir is raised in a vertical...Ch. 3 - The barometer of a mountain hiker reads 980 mbars...Ch. 3 - The basic barometer can be used to measure the...Ch. 3 - Prob. 28PCh. 3 - Prob. 29EPCh. 3 - A gas is contained in a vertical, frictionless...Ch. 3 - Both a gage and a manometer are attached to a gas...Ch. 3 - The variation of pressure P in a gas with density ...Ch. 3 - The system shown in the figure is used to...Ch. 3 - The manometer shown in the figure is designed to...Ch. 3 - A manometer containing ( =850kg/m3 ) attached to a...Ch. 3 - A mercury ( =13,600kg/m3 ) is connected to an air...Ch. 3 - Repeat Prob. 3-37 for a differential mercury...Ch. 3 - Blood pressure is usually measured by rapping a...Ch. 3 - The maximum blood pressure in the upper arm of a...Ch. 3 - Consider a 1.73-m-tall man standing vertically in...Ch. 3 - Consider a U-tube whose arms are open to the...Ch. 3 - Prob. 44PCh. 3 - Freshwater and seamier flowing in parallel...Ch. 3 - Repeat Prob. 3-48 by replacing the air with oil...Ch. 3 - The pressure in a natural gas pipeline is measured...Ch. 3 - Repeat Prob. 3-42E by replacing air by oil with a...Ch. 3 - The gage pressure of the air in the tank shown in...Ch. 3 - Repeat Prob. 3-44 for a gage pressure of 40 kPa.Ch. 3 - The 500-kg load on the hydraulic lift show in Fig....Ch. 3 - Prob. 52EPCh. 3 - Pressure is often given in terms of a liquid...Ch. 3 - Prob. 54PCh. 3 - Consider a double-fluid manometer attached to an...Ch. 3 - The pressure difference between an oil pipe and...Ch. 3 - Consider the system shown in Fig. P3-51. If a...Ch. 3 - Prob. 58PCh. 3 - Prob. 59PCh. 3 - Define the resultant hydrostatic force acting on a...Ch. 3 - Someone claims that she can determine the...Ch. 3 - A submersed horizontal flat plate is suspended in...Ch. 3 - You may have noticed that dams are much thicker at...Ch. 3 - Consider a submerged curved surface. Explain how...Ch. 3 - Consider a submersed curved surface. Explain how...Ch. 3 - Consider a circular surface subjected to...Ch. 3 - Consider a heavy car submerged in water in a lake...Ch. 3 - A long, solid cylinder of radius 2 ft hinged at...Ch. 3 - Consider a 8-m-long, 8-m-wide, and 2-m-high...Ch. 3 - Consider a 200-ft-high, dam filled to capacity....Ch. 3 - A room the lower level of a cruise ship has a...Ch. 3 - The water side of the wall of a 70-m-long dam is a...Ch. 3 - For a gate width of 2 m into the paper (Fig....Ch. 3 - Determine the resultant force acting on the...Ch. 3 - A 6-m-high, 5-m-wide rectangular plate blocks the...Ch. 3 - The flow of water from a reservoir is controlled...Ch. 3 - Repeat Prob. 3-76E for a water height of 6 ft.Ch. 3 - A water trough of semicircular cross section of...Ch. 3 - Prob. 80PCh. 3 - An open settling tank shown in the figure contains...Ch. 3 - From Prob. 3-80, knowing that the density of the...Ch. 3 - Prob. 83PCh. 3 - The two sides of a V-shaped water trough are...Ch. 3 - Repeat Prob. 3-82 for the case of a partially...Ch. 3 - A retaining wall against a mud slide is to be...Ch. 3 - Prob. 87PCh. 3 - A 4-m-long quarter-circular gate of radius 3 m and...Ch. 3 - Repeat Prob. 3-90 for a radius of 2 m for the...Ch. 3 - Consider a flat plate of thickness t, width w into...Ch. 3 - Prob. 91PCh. 3 - Consider a 1-m wide inclined gate of negligible...Ch. 3 - Prob. 93PCh. 3 - What is buoyant force? What causes it? What is the...Ch. 3 - Consider two identical spherical bails submerged...Ch. 3 - Consider two 5-cm-diaineter spherical balls-one...Ch. 3 - Prob. 97CPCh. 3 - Prob. 98CPCh. 3 - The density of a liquid is to be determined by an...Ch. 3 - A crane is used to lower weights into a lake for...Ch. 3 - Prob. 101PCh. 3 - Prob. 102PCh. 3 - Prob. 103PCh. 3 - It is estimated that 90 percent of an iceberg’s...Ch. 3 - The weight of a body is usually measured by...Ch. 3 - Prob. 106PCh. 3 - Prob. 107PCh. 3 - The hull of a boat has a volume of 180 m3, and the...Ch. 3 - Under what conditions can a moving body of fluid...Ch. 3 - Consider a glass of water. Compare the water...Ch. 3 - Consider two identical glasses of water, one...Ch. 3 - Consider a vertical cylindrical container...Ch. 3 - Prob. 113PCh. 3 - Consider two water tanks filled with water. The...Ch. 3 - Prob. 115PCh. 3 - A 3-ft-diameter vertical cylindrical lank open to...Ch. 3 - Prob. 117PCh. 3 - A 30-cm-diameter, 90-cm-high vertical cylindrical...Ch. 3 - A fish tank that contains 60-cm-high water is...Ch. 3 - A 3-m-diameter vertical cylindrical milk tank...Ch. 3 - Consider a tank of rectangular cross-section...Ch. 3 - The bottom quarter of a vertical cylindrical tank...Ch. 3 - Milk with a density of 1020 kg/m3 is transported...Ch. 3 - Prob. 124PCh. 3 - The distance between the centers of the two arms...Ch. 3 - A 1.2-m-diameter, 3-m-high scaled vertical...Ch. 3 - A15-ft-long, 6-ft-high rectangular tank open to...Ch. 3 - An 8-ft-long tank open to the atmosphere initially...Ch. 3 - A 3-m-diameter, 7-m-long cylindrical tank is...Ch. 3 - Prob. 131PCh. 3 - Prob. 132PCh. 3 - Prob. 133PCh. 3 - Prob. 134PCh. 3 - An air-conditioning system requires a 34-m-long...Ch. 3 - Prob. 136PCh. 3 - If the rate of rotational speed of the 3-tube...Ch. 3 - A 30-cm-diameter vertical cylindrical vessel is...Ch. 3 - Prob. 139PCh. 3 - Prob. 141PCh. 3 - Prob. 142EPCh. 3 - The basic barometer can be used as an...Ch. 3 - The lower half of a 12-m-high cylindrical...Ch. 3 - A vertical, frictionless pistoncylinder device...Ch. 3 - A pressure cooker cooks a lot faster than an...Ch. 3 - Prob. 147PCh. 3 - The average atmospheric pressure on earth is...Ch. 3 - When measuring small pressure differences with a...Ch. 3 - Prob. 150EPCh. 3 - Prob. 151PCh. 3 - A gasoline line is connected to a pressure gage...Ch. 3 - Prob. 154PCh. 3 - Prob. 155EPCh. 3 - The pressure of water flowing through a pipe is...Ch. 3 - Consider a U-tube filled with mercury as shown in...Ch. 3 - Prob. 158PCh. 3 - The variation of pressure with density in a thick...Ch. 3 - A 3-m-high. 5-m-wide rectangular gale is hinged al...Ch. 3 - Prob. 161PCh. 3 - A semicircular 40-ft-diameter tunnel is to be...Ch. 3 - A 30-ton. 4-m-diameter hemispherical dome on a...Ch. 3 - The water in a 25-m-deep reservoir is kept inside...Ch. 3 - Prob. 165PCh. 3 - A 1-m-diameter, 2-m-high vertical cylinder is...Ch. 3 - A 5-m-long, 4-m-high tank contains 2.5-m-deep...Ch. 3 - Prob. 169PCh. 3 - Prob. 170PCh. 3 - The density of a floating body can be determined...Ch. 3 - The 280-ke, 6-m-wide rectangular gate shown in Fig...Ch. 3 - Prob. 173PCh. 3 - Prob. 174PCh. 3 - Prob. 175PCh. 3 - The gage pressure in a pipe is measured by a...Ch. 3 - Prob. 177PCh. 3 - Prob. 178PCh. 3 - Prob. 179PCh. 3 - Consider the vertical rectangular wall of a water...Ch. 3 - Prob. 181PCh. 3 - Prob. 182PCh. 3 - Prob. 183PCh. 3 - Prob. 184PCh. 3 - Prob. 185PCh. 3 - Consider a 6-m-diameter spherical sate holding a...Ch. 3 - Prob. 188PCh. 3 - Prob. 189PCh. 3 - Prob. 190PCh. 3 - Prob. 191PCh. 3 - Prob. 192PCh. 3 - A 15-cm-diameter, 40-cm-high vertical cylindrical...Ch. 3 - Prob. 194PCh. 3 - Prob. 195PCh. 3 - Shoes are to be designed to enable people of up to...Ch. 3 - The volume of a rock is to be determined without...Ch. 3 - The density of stainless steel is about 8000 kg/m3...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (b) Consider two identical water tanks (20 m x 10 m x 10 m) filled with water. The depth of water in the first tank is 8 m and it is stationary. The depth of water in the second tank is 6 m and it is moving vertically downward with a constant acceleration of 3.3 m/s?. Which tank will have a higher pressure at the bottom? Now, the first tank is moving horizontally in the direction of its length with a constant acceleration of 2.4 m/s?. Determine the shape of the free surface and the total force on the base and vertical faces of this tank. What will happen if these tanks are completely filled with water?arrow_forwardA capillary tube of 1.55 mm diameter is immersed vertically in water exposed to the atmosphere. Determine how high water will rise in the tube. Take the contact angle at the inner wall of the tube to be 6° and the surface tension to be 1.00 N/m. Take the density os water to be 1000 kg/m³. The water will rise m in the tube.arrow_forwardThe truck carries an open rectangular container that is 3.9m wide, 3.0m deep and 5.0m long, contains oil of density 811kg/m³ to a depth of 2.1m. If it has a constant acceleration of 6.9m/s². Determine the total force(in kN) acting at the rear wall of the container.arrow_forward
- Consider a body of arbitrary shape. If the pressure distribution over thesurface of the body is constant, prove that the resultant pressure force onthe body is zero.arrow_forwardA cylindrical tank contained air with an absolute pressure of 60 kPa and has a temperature of 60 °C. Determine the mass of air in the tank. Tank dimension: 4 m high with 1.5 m radius.arrow_forwardUnder what conditions can a moving body of fluid be treated as a rigid body?arrow_forward
- A 5-m-long, 4-m-high tank contains 2.5-m-deep water when not in motion and is open to the atmosphere through a vent in the middle. The tank is now accelerated to the right on a level surface at 2 m/s2. Determine the maximum pressure in the tank relative to the atmospheric pressurearrow_forwardA volume of 8 m3 of oxygen initially at 80 kPa of absolute pressure and 15∘C is subjected to an absolute pressure of 21 kPa while the temperature remains constant. Determine the density of the oxygen and the new volume of the oxygen.arrow_forwardA u_tube whose arms are open to the atmosphere. Now equal volumes of water and light oil. (density =49.4kg/m^3)are poured from different arms. A person blows from the oil side of the u_tube until the contact surface of the two fluid moves to the bottom u_tube, and thus the liquid levels in the two arms are the same .if the fluid height in each arm is 30in,Determine the gauge pressure the person exerts on the oil by blowing.arrow_forward
- Consider a vertical cylindrical container partially filled with water. Now the cylinder is rotated about its axis at a specified angular velocity, and rigid-body motion is established. Discuss how the pressure will be affected at the midpoint and at the edges of the bottom surface due to rotation.arrow_forwardSome rocks or bricks contain small air pockets in them and have a spongy structure. Assuming the air spaces form columns of an average diameter of 5 µm, determine how high water can rise in such a material. Take the surface tension of the air-water interface in that material to be 0.085 N/m. The capillary rise in such a material is m.arrow_forward1. The compressed air tank has a volume of 0.6 m. The temperature is 15°C and the atmospheric pressure is 101.35 kPa. When the tank is filled with air at a gage pressure of 244.74 kPa, determine the density of the air and the weight of air in the tank. Hint: Ideal gas law should be used. R-287 m/sKarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY