Explanation Given information: The constant angular velocity is ω , the gravitational constant is g , the height of the U tube is h , and the length is L . The figure below shows the schematic diagram for the U tube. Figure-(1) Write the expression for the pressure difference by applying the Bernoulli’s equation between point 1 and 2. P 1 ρ g + V 1 2 2 g + z 1 = P 2 ρ g + V 2 2 2 g + z 2 P 1 ρ g + ( ω r 1 ) 2 2 g + z 1 = P 2 ρ g + ( ω r 2 ) 2 2 g + z 2 z 1 − z 2 = P 2 − P 1 ρ g + ( ω r 2 ) 2 − ( ω r 1 ) 2 2 g 0 = P 2 − P 1 ρ g + ( ω r 2 ) 2 − ( ω r 1 ) 2 2 g Δ P ρ g = ( ω r 2 ) 2 − ( ω r 1 ) 2 2 g ...... (I) Here, the change in the pressure is Δ P , the velocity of the liquid is V , and the density of the liquid is ρ . Write the expression for the pressure at point 1. P 1 = ρ g ( h + h 2 ) ...... (II) Write the expression for the pressure at point 2. P 2 = ρ g ( h 2 ) ...... (III) Write the expression for the change in pressure. Δ P = P 2 − P 1 ...... (IV) Calculation: Substitute ρ g ( h + h 2 ) for P 1 and ρ g ( h 2 ) for P 2 in Equation (IV)

Fluid Mechanics Fundamentals And Applications

3rd Edition

ISBN: 9780073380322

Author: Yunus Cengel, John Cimbala

Publisher: MCGRAW-HILL HIGHER EDUCATION

See similar textbooks

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. T…

Videos

Question

Chapter 3, Problem 134P

To determine

The relation for the angular velocity in terms of g, h and l.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 3, Problem 133P

Chapter 3, Problem 135P

Students have asked these similar questions

The gears shown in the figure have a diametral pitch of 2 teeth per inch and a 20° pressure angle. The pinion rotates at 1800 rev/min clockwise and transmits 200 hp through the idler pair to gear 5 on shaft c. What forces do gears 3 and 4 transmit to the idler shaft? TS I y 18T 32T This a 12 x 18T C 48T 5

Question 1. Draw 3 teeth for the following pinion and gear respectively. The teeth should be drawn near the pressure line so that the teeth from the pinion should mesh those of the gear. Drawing scale (1:1). Either a precise hand drawing or CAD drawing is acceptable. Draw all the trajectories of the involute lines and the circles. Specification: 18tooth pinion and 30tooth gear. Diameter pitch=P=6 teeth /inch. Pressure angle:20°, 1/P for addendum (a) and 1.25/P for dedendum (b). For fillet, c=b-a.

5. The figure shows a gear train. There is no friction at the bearings except for the gear tooth forces. The material of the milled gears is steel having a Brinell hardness of 170. The input shaft speed (n2) is 800 rpm. The face width and the contact angle for all gears are 1 in and 20° respectively. In this gear set, the endurance limit (Se) is 15 kpsi and nd (design factor) is 2. (a) Find the revolution speed of gear 5. (b) Determine whether each gear satisfies the design factor of 2.0 for bending fatigue. (c) Determine whether each gear satisfies the design factor of 2.0 for surface fatigue (contact stress). (d) According to the computation results of the questions (b) and (c), explain the possible failure mechanisms for each gear. N4=28 800rpm N₁=43 N5=34 N₂=14 P(diameteral pitch)=8 for all gears Coupled to 2.5hp motor

Chapter 3 Solutions

Fluid Mechanics Fundamentals And Applications

Ch. 3 - Someone claims that the absolute pressure in a...Ch. 3 - A tinysteel cube is suspended in water by a...Ch. 3 - Express Pascal’s law, and give a real-world...Ch. 3 - Consider two identical fans, one at sea level and...Ch. 3 - What is the difference between gage pressure and...Ch. 3 - Explain why some people experience nose bleeding...Ch. 3 - Prob. 7P Ch. 3 - A vacuum gage connected to a chamber reads 36 kPa...Ch. 3 - The pressure at the exit of an air compressor is...Ch. 3 - The pressure in a water line is 1500 kPa. What is...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The relation for the angular velocity in terms of g , h and l .

Solution Summary: The author explains the relation for the angular velocity in terms of g, h and l.

Concept explainers

Videos

The relation for the angular velocity in terms of g, h and l.

Want to see the full answer?

Chapter 3 Solutions