DeGarmo's Materials and Processes in Manufacturing

12th Edition

ISBN: 9781118987674

Author: J. T. Black, Ronald A. Kohser

Publisher: WILEY

See similar textbooks

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many …

Videos

Textbook Question

Chapter 22, Problem 36RQ

What is a honed edge on a cutting tool and why is it done?

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 22, Problem 35RQ

Chapter 22, Problem 1P

Students have asked these similar questions

Just give a short answer (type written) 1. How is a tool bit blank prepared for use? 2. What is a carbide insert method for cutting tool? 3.Can the shape and condition of the cutting tool slow down the machining of metal?

Define the fundamental of cutting.

What are the functions of cutting fluid?

Chapter 22 Solutions

DeGarmo's Materials and Processes in Manufacturing

Ch. 22 - For metal-cutting tools, what is the most...Ch. 22 - What is hot hardness compared to hardness?Ch. 22 - Prob. 3RQ Ch. 22 - Why is impact strength an important property in...Ch. 22 - Cemented carbide tools are made by a powder...Ch. 22 - What are the primary considerations in tool...Ch. 22 - What is the general strategy behind coated tools?Ch. 22 - Prob. 8RQ Ch. 22 - How is a CBN tool manufactured?Ch. 22 - Prob. 10RQ

Ch. 22 - Prob. 11RQ Ch. 22 - Discuss the constraints in the selection of a...Ch. 22 - What does cemented mean in the manufacture of...Ch. 22 - What advantage do ground carbide inserts have over...Ch. 22 - What is a chip groove?Ch. 22 - What is the DCL?Ch. 22 - Suppose you made four beams out of carbide, HSS,...Ch. 22 - Multiple coats or layers are put on the carbide...Ch. 22 - What tool material would you recommend for...Ch. 22 - What makes the process that makes TiC coatings for...Ch. 22 - Why does a TiN-coated tool consume less power than...Ch. 22 - For what work material are CBN tools more commonly...Ch. 22 - Why is CBN better for machining steel than...Ch. 22 - What is the typical coefficient of variation for...Ch. 22 - What is meant by the statement Tool life is a...Ch. 22 - The typical value of a coefficient of variation in...Ch. 22 - Machinability is defined in many ways. Explain how...Ch. 22 - What are the chief functions of cutting fluids?Ch. 22 - Prob. 29RQ Ch. 22 - Why is the PVD process used to coat HSS tools?Ch. 22 - Why is there no universal cutting tool material?Ch. 22 - What is an 18-4-1 HSS composed of?Ch. 22 - Over the years, tool materials have been developed...Ch. 22 - Why is the rigidity of the machine tool an...Ch. 22 - Explain how it can be that the tool wears when it...Ch. 22 - What is a honed edge on a cutting tool and why is...Ch. 22 - Suppose you have a turning operation using a tool...Ch. 22 - A 2 in.-diameter bar of steel was turned at 284...Ch. 22 - Prob. 3P Ch. 22 - The following data have been obtained for...Ch. 22 - In the insert is set with a 0 side cutting-edge...Ch. 22 - Prob. 6P Ch. 22 - Here is a single point tool. Identify angles A...Ch. 22 - Figure 22.B gives data for cutting speed and tool...

Additional Engineering Textbook Solutions

Find more solutions based on key concepts

Using the results of Problems 1.63-1.65, generate a statement about the general design approach to achieving a ...

Applied Fluid Mechanics (7th Edition)

37. A 10-liter [L] flask contains 5 moles [mol] of gas at a pressure of 15 atmospheres [atm]. What is the tempe...

Thinking Like an Engineer: An Active Learning Approach (4th Edition)

The throttle-control lever OA rotates in the range 090. An internal torsional return spring exerts a restoring ...

Engineering Mechanics: Statics

If the gap between C and the rigid wall at D is initially 0.15 mm, determine the support reactions at A and D w...

Mechanics of Materials (10th Edition)

A large beverage cooler resembles a small building and is to be maintained at about 35 F (2 C) and a low relati...

Heating Ventilating and Air Conditioning: Analysis and Design

2.3 Compute the vertical and horizontal components for each of the forces shown.

Applied Statics and Strength of Materials (6th Edition)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.