Concept explainers
SSM Consider the slab shown in Fig. 18-18. Suppose that L = 25.0 cm, A = 90.0 cm2, and the material is copper. If TH = 125°C, TC = 10.0°C, and a steady state is reached, find the
Figure 18-18 Thermal conduction. Energy is transferred as heat from a reservoir at temperature TH to a cooler reservoir at temperature TC through a conducting slab of thickness L and thermal conductivity k.
Want to see the full answer?
Check out a sample textbook solutionChapter 18 Solutions
Fundamentals of Physics Extended
Additional Science Textbook Solutions
Living By Chemistry: First Edition Textbook
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
College Physics: A Strategic Approach (3rd Edition)
Laboratory Experiments in Microbiology (12th Edition) (What's New in Microbiology)
Human Physiology: An Integrated Approach (8th Edition)
Microbiology: An Introduction
- (a)Calculate the rate of heat conduction (in W) through house walls that are 10.5 cm thick and that have an average thermal conductivity twice that of glass wool. Assume there are no windows or doors. The surface area of the walls is 145 m2 and their inside surface is at 21.5°C, while their outside surface is at 5.00°C. ________________ W (b)How many 1 kW room heaters would be needed to balance the heat transfer due to conduction? (Round your answer to the next whole integer.) ______________________ 1 kW room heatersarrow_forwardNEED ANSWER ASAP At a temperature of 33.7 °C a 0.42-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 122.8°C, determine the change in length of the steel rod if L = 321.85 mm and M = 211 mm. Round off the final answer to four decimal places.arrow_forwardA heat conducting rod, 0.90 m long, is made of an aluminum section that is 0.10 m long, and an unknown material section that is 0.80 m long. Both sections have the same cross-sectional area. The aluminum end (rod 2) is maintained at a temperature of 50°C and the unknown material end (rod 1) is at 150°CTThe thermal conductivity of aluminum is 205 W/m-K and the junction temperature is 65°C. Steady state has been reached, and no heat is lost through the well-insulated sides of the rod. Find the thermal conductivity (k) of the unknown material. H T Rod 2 Rod 1arrow_forward
- (a) The data listed in the following table gives hourly measurements of heat flux q (W/m²) at the surface of a solar collector. As an engineer, you estimated the total heat absorbed by a 4 m collector panel during a 13-hr period as h =122.39 W. The panel has an absorption efficiency eab of 45%. If the total heat absorbed is given by h = eab q A dt where A = area and q = heat flux, find K. t 0 1 3 4 5 7 9 11 13 0.10 4.32 5.14 6.05 7.73 K 7.23 5.20 3.38 0.20arrow_forwardAir Ice Water A 5.0 cm slab has formed on an outdoor tank of water (Fig. 18-47). The air is at – 10°C. Find the rate of ice formation (centimeters per hour). The ice has thermal con- ductivity 0.0040 cal/s-cm-C and density 0.92 g/cm. Assume there is no energy transfer through the walls or bottom. Figure 18-47 Problem 61.arrow_forwardb) The heat capacity of solid lead oxide [PbO (s)] is given by Cp.m JK- mol = 44.35 – 1.47 × 10-32 Calculate the change in molar enthalpy (AHm) (in unit J mol*) of PbO (s) if it is cooled from 500 K to 300 K at constant pressure (P). Quantity Cp,m denotes molar heat capacity at constant pressure.arrow_forward
- A large heat exchanger transfers a total of 100 MW. Assume the wall separating steam and seawater is 4 mm of steel, conductivity 15 W/m K and that a maximum of 5°C difference between the two fluids is allowed. Find the required minimum area for the heat transfer.arrow_forwardo42 0 A 20.0 g copper ring at 0.000°C has an inner diameter of D = 2.54000 cm. An aluminum sphere at 100.0°C has a diameter of d = 2.545 08 cm. The sphere is put on top of the ring (Fig. 18-36), and the two are allowed to come to thermal equilibrium, with no heat lost to the surroundings. The sphere just passes through the ring at the equilibrium tempera- ture. What is the mass of the Al Cu Figure 18-36 Problem 42. sphere?arrow_forwardThe amount of thermal expansion coefficient (a) if the length of a copper rod is (5 m) at a temperature (20) and at a temperature (60), the length of the wire will increase to (Ans = (5.0036 m d = 18x10 deg / %3Darrow_forward
- Imagine a person standing naked in a room at 23.3°C. The walls are well insulated, so they also are at 23.3°C. The person’s surface area is 2.20 m2, and his basal metabolic rate is 2167 kcal/day. His emissivity is 0.970. a) If the person’s skin temperature were 35.7°C (the same as the internal body temperature), at what net rate would heat be lost through radiation? (Ignore losses by conduction and convection.) b) The heat loss is not sustainable—but skin temperature is less than internal body temperature. What will be the skin temperature( in Celsius) such that the net heat loss due to radiation is equal to the basal metabolic rate? c) How does wearing clothing slow the loss of heat? Choose one of the following: a. by convection b. by conduction and convection c. by conduction d. by radiationarrow_forwardA liquid food is being cooled from 80°C to 30°C in a direct heat exchanger using cold water as a cooling medium. If the product mass flow rate us 1800 kg/h, determine the water flow rate required to accomplish product cooling if the water is allowed to increase its temperature from 10°C to 20°C in the heat exchanger. The specific heat of the product is 3.8 kJ/kg K, and the value for water is 4.1 kJ/kg K. Answer must be 8,341.5 Kg/harrow_forwardFigure 18-46 shows the cross section of a wall made of three layers. The layer thicknesses are L1, L2 = TH 0.700L1, and L3 0.350L1. The ther- Tc mal conductivities are k1, k2 = 0.900k1, and kz - 0.800k1. The temper- L Ls atures at the left side and right side of Figure 18-46 Problem 60. the wall are TH = 30.0°C and Tc = %3D -15.0°C, respectively. Thermal conduction is steady. (a) What is the temperature difference AT2 across layer 2 (between the left and right sides of the layer)? If k, were, instead, equal to 1.1k1, (b) would the rate at which energy is con- ducted through the wall be greater than, less than, or the same as pre- viously, and (c) what would be the value of AT,?arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning