
Concept explainers
(a)
Find the change in the angular velocity of the turbine disk.
(a)

Answer to Problem 17.24P
The change in angular velocity of the turbine disk is
Explanation of Solution
Given information:
The mass of the turbine disk is
The centroidal radius of gyration of the turbine disk is
The angular velocity of the small blade is
The weight of the small blade is
The centroidal radius of the blade is
The angle the turbine disk rotates is
Position 1:
Find the mass of inertia about point O
Here, the acceleration due to gravity is g.
Consider the acceleration due to gravity is
Substitute 30 kg for
Find the location of mass center
Position 1
The angular velocity at the position 1 is
Find the total kinetic energy
Substitute
Find the total potential energy
Here, the conditional center of gravity is
In this case, the center of gravity lies at the point O. so,
Substitute 0 for
Position 2
Find the total kinetic energy
Substitute
Find the total potential energy
Here, the conditional center of gravity is
In this case, the center of gravity lies at the point O. so,
Substitute
Substitute 30 kg for
Write the equation of conservation of energy as follows;
Substitute 18.04480 J for
Find the change in angular velocity
Substitute 59.75 rpm for
Therefore, the change in angular velocity of the turbine disk is
(b)
Find the change in the angular velocity of the turbine disk.
(b)

Answer to Problem 17.24P
The change in angular velocity of the turbine disk is
Explanation of Solution
Given information:
The mass of the turbine disk is
The centroidal radius of gyration of the turbine disk is
The angular velocity of the small blade is
The weight of the small blade is
The centroidal radius of the blade is
The angle the turbine disk rotates is
Position 1:
Find the mass of inertia about point O
Here, the acceleration due to gravity is g.
Consider the acceleration due to gravity is
Substitute 30 kg for
Find the location of mass center
Position 1
The angular velocity at the position 1 is
Find the total kinetic energy
Substitute
Find the total potential energy
Here, the conditional center of gravity is
In this case, the center of gravity lies at the point O. so,
Substitute 0 for
Position 3
Find the total kinetic energy
Substitute
Find the total potential energy
Here, the conditional center of gravity is
In this case, the center of gravity lies at the point O. so,
Substitute
Substitute 30 kg for
Write the equation of conservation of energy as follows;
Substitute 18.04480 J for
Find the change in angular velocity
Substitute 60.249 rpm for
Therefore, the change in angular velocity of the turbine disk is
Want to see more full solutions like this?
Chapter 17 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
- CORRECT AND DETAILED SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. I NEED FBD A short plate is attached to the center of the shaft as shown. The bottom of the shaft is fixed to the ground.Given: a = 75 mm, h = 125 mm, D = 38 mmP1 = 24 kN, P2 = 28 kN1. Calculate the maximum torsional stress in the shaft, in MPa.2. Calculate the maximum flexural stress in the shaft, in MPa.3. Calculate the maximum horizontal shear stress in the shaft, in MPa.ANSWERS: (1) 167.07 MPa; (2) 679.77 MPa; (3) 28.22 MPaarrow_forwardCORRECT AND DETAILED SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. I REALLY NEED FBD. The roof truss shown carries roof loads, where P = 10 kN. The truss is consisting of circular arcs top andbottom chords with radii R + h and R, respectively.Given: h = 1.2 m, R = 10 m, s = 2 m.Allowable member stresses:Tension = 250 MPaCompression = 180 MPa1. If member KL has square section, determine the minimum dimension (mm).2. If member KL has circular section, determine the minimum diameter (mm).3. If member GH has circular section, determine the minimum diameter (mm).ANSWERS: (1) 31.73 mm; (2) 35.81 mm; (3) 18.49 mmarrow_forwardPROBLEM 3.23 3.23 Under normal operating condi- tions a motor exerts a torque of magnitude TF at F. The shafts are made of a steel for which the allowable shearing stress is 82 MPa and have diameters of dCDE=24 mm and dFGH = 20 mm. Knowing that rp = 165 mm and rg114 mm, deter- mine the largest torque TF which may be exerted at F. TF F rG- rp B CH TE Earrow_forward
- 1. (16%) (a) If a ductile material fails under pure torsion, please explain the failure mode and describe the observed plane of failure. (b) Suppose a prismatic beam is subjected to equal and opposite couples as shown in Fig. 1. Please sketch the deformation and the stress distribution of the cross section. M M Fig. 1 (c) Describe the definition of the neutral axis. (d) Describe the definition of the modular ratio.arrow_forwardusing the theorem of three moments, find all the moments, I only need concise calculations with minimal explanations. The correct answers are provided at the bottomarrow_forwardMechanics of materialsarrow_forward
- practise questionarrow_forwardCan you provide steps and an explaination on how the height value to calculate the Pressure at point B is (-5-3.5) and the solution is 86.4kPa.arrow_forwardPROBLEM 3.46 The solid cylindrical rod BC of length L = 600 mm is attached to the rigid lever AB of length a = 380 mm and to the support at C. When a 500 N force P is applied at A, design specifications require that the displacement of A not exceed 25 mm when a 500 N force P is applied at A For the material indicated determine the required diameter of the rod. Aluminium: Tall = 65 MPa, G = 27 GPa. Aarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





