Degarmo's Materials And Processes In Manufacturing
Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
bartleby

Concept explainers

Forming and Shaping
Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the s…
bartleby

Videos

Question
Book Icon
Chapter 17, Problem 67RQ
To determine

The reason for no standard test to assess or quantify formability.

Expert Solution & Answer
Check Mark

Want to see the full answer?

Check out a sample textbook solution
Blurred answer
Previous
Chapter 17, Problem 66RQ
Next
Chapter 17, Problem 1P
Students have asked these similar questions
The sketch below gives some details of the human heart at rest. What is the total power requirement (work/time) for an artificial heart pump if we use a safety factor of 5 to allow for inefficiencies, the need to operate the heart under stress, etc.? Assume blood has the properties of water. p pressure above atmosphere blood going to the lungs for a fresh charge of oxygen p = 2.9 kPa 25v pulmonary artery d = 25mm fresh oxygenated blood from the lungs p = 1.0 kPa vena cava d=30mm right auricle pulmonary vein, d = 28mm aorta, d=20mm spent blood returning from left auricle the body p = 0.66 kPa right left ventricle ventricle blood to feed the body, p 13 kPa normal blood flow = 90 ml/s
4- A horizontal Venturi meter is used to measure the flow rate of water through the piping system of 20 cm I.D, where the diameter of throat in the meter is d₂ = 10 cm. The pressure at inlet is 17.658 N/cm2 gauge and the vacuum pressure of 35 cm Hg at throat. Find the discharge of water. Take Cd = 0.98.
10

Chapter 17 Solutions

Degarmo's Materials And Processes In Manufacturing

Ch. 17 - What is plasticity?Ch. 17 - What are some of the general assets of the...Ch. 17 - Why might large production quantities be necessary...Ch. 17 - What types of deformation may occur in forming...Ch. 17 - What is an independent variable in a...Ch. 17 - What are some considerations regarding selection...Ch. 17 - What is the significance of tool and die geometry...Ch. 17 - Why is lubrication often a major concern in metal...Ch. 17 - What are some of the secondary effects that may...Ch. 17 - Prob. 10RQ
Ch. 17 - Why is it important to be able to predict the...Ch. 17 - Prob. 12RQCh. 17 - Prob. 13RQCh. 17 - Prob. 14RQCh. 17 - Prob. 15RQCh. 17 - Prob. 16RQCh. 17 - Prob. 17RQCh. 17 - What are some of the features that may be...Ch. 17 - What features have contributed to the expanded use...Ch. 17 - What are some of the uses or applications of...Ch. 17 - Prob. 21RQCh. 17 - Prob. 22RQCh. 17 - Prob. 23RQCh. 17 - What type of information about the material being...Ch. 17 - Prob. 25RQCh. 17 - Why is friction such an important parameter in...Ch. 17 - Why are friction effects in metalworking difficult...Ch. 17 - Prob. 28RQCh. 17 - Prob. 29RQCh. 17 - Prob. 30RQCh. 17 - Prob. 31RQCh. 17 - Discuss the significance of wear in metal forming:...Ch. 17 - Lubricants are often selected for properties in...Ch. 17 - What is tribology?Ch. 17 - What are some of the common types of metal forming...Ch. 17 - What is hydrodynamic lubrication? What are some of...Ch. 17 - If the temperature of a material is increased,...Ch. 17 - Define the various regimes of cold working, warm...Ch. 17 - What is an acceptable definition of hot working?...Ch. 17 - What are some of the attractive manufacturing and...Ch. 17 - What are some of the negative aspects of hot...Ch. 17 - Prob. 42RQCh. 17 - Prob. 43RQCh. 17 - If the deformed grains recrystallize during hot...Ch. 17 - Why might a rolled thread offer improved strength...Ch. 17 - How might the temperature of a deforming workpiece...Ch. 17 - Why are heated dies or tools often employed in...Ch. 17 - What generally restricts the upper temperature to...Ch. 17 - What is the primary cause of residual stresses in...Ch. 17 - What is cold working?Ch. 17 - Compared to hot working, what are some of the...Ch. 17 - What are some of the disadvantages of...Ch. 17 - How could cold working be used to reduce the cost...Ch. 17 - Why are cold�forming processes best suited for...Ch. 17 - How can the tensile test properties of a metal be...Ch. 17 - Why is elastic springback an important...Ch. 17 - What is pickling, and how does it remove surface...Ch. 17 - Prob. 58RQCh. 17 - What engineering properties are likely to decline...Ch. 17 - Prob. 60RQCh. 17 - Prob. 61RQCh. 17 - Prob. 62RQCh. 17 - What are some of the advantages of warm forming...Ch. 17 - Prob. 64RQCh. 17 - What material feature is considered to be the...Ch. 17 - Why is isothermal forming considerably more...Ch. 17 - Prob. 67RQCh. 17 - Prob. 1PCh. 17 - Prob. 2PCh. 17 - List and discuss the various economic factors that...Ch. 17 - Prob. 4PCh. 17 - Prob. 5PCh. 17 - Prob. 6PCh. 17 - Prob. 1.1CSCh. 17 - Prob. 1.2CSCh. 17 - Which stainless steel would you recommend? Begin...Ch. 17 - Prob. 1.4CSCh. 17 - Prob. 1.5CSCh. 17 - After drawing and perforating, the residual...Ch. 17 - One of the blades has struck a rock and is badly...Ch. 17 - A second propeller, identical to the one above,...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
SEE MORE TEXTBOOKS
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License