A sign て is constructed from 7 mm thick plate steel (density 8000 kg/m³) with the geometry shown in the figure. The sign is connected to the wall by a pin at A and also supported by member DE. Support member DE is also constructed from 7 mm thick plate steel and is connected by pins at B and E respectively. Determine the reaction forces at A and E. Enter your answers in Cartesian components. The weights of both the sign D and member DE should be accounted for in the calculation. Assume the pins are located a distance cm away from the ends at each connection. พ 2 D W E CC ④ BY NC SA 2016 Eric Davishahl Ул B D W. -b- W C h Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 2 m b 2.6 m с 1.6 m h 1.82 m พ 3 10 cm The reaction at A is A = The reaction at E is E = 2.> i+ Ĵ N. i+ ĴN.

A sign て is constructed from 7 mm thick plate steel (density 8000 kg/m³) with the geometry shown in the figure. The sign is connected to the wall by a pin at A and also supported by member DE. Support member DE is also constructed from 7 mm thick plate steel and is connected by pins at B and E respectively. Determine the reaction forces at A and E. Enter your answers in Cartesian components. The weights of both the sign D and member DE should be accounted for in the calculation. Assume the pins are located a distance cm away from the ends at each connection. พ 2 D W E CC ④ BY NC SA 2016 Eric Davishahl Ул B D W. -b- W C h Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 2 m b 2.6 m с 1.6 m h 1.82 m พ 3 10 cm The reaction at A is A = The reaction at E is E = 2.> i+ Ĵ N. i+ ĴN.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.112P: The inside surface of each thin shell carries a uniform normal pressure of intensity p0. Compute R,...

See similar textbooks

Similar questions

provide complete and correct solution
An old single-leaf drawbridge is made of a thin rectangular board of mass M, width a(into the page) and length bwhich can pivot at oneend. When it is not in use, the span of the bridge is held at a 60ºangle from the horizontal direction. The two ideal cables that holdit at itsfarther end areanchored to the ground so that they forma 30º angle with the horizontal direction, as shown in Fig. 3.The acceleration due to gravity has magnitude g. a) Set up all the detailed scalar equations (not the general version)expressing the static equilibrium of the drawbridge. b) Determine the magnitude T of the tension force exerted by each of the two cables on the board. c)Determine the magnitude Fh of the hinge force exerted on the board and the angle h that the force forms with respect to the horizontal direction.
Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure pagainst the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). 42 45 100 Ib 18 3 ft 3 ft- 30 200 Ib ft 30" 30 30 kg 2 ft B B Fig (1) Fig (2) Fig (3)
The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which is in tension as shown. DA 1.5 m 60° 1.2 m What are the components of the Weight Vector (W), which is used to represent the weight of the bar OA W =Wi – Wyj (Answer in Newtons) Wy Choose... Choose... Next page us page
I can't find C or D
The frame of a machine is accelerated rightwards at 3/4 gravity as shown in the figure below, it carries a uniform angle ABC weighing 120 lbs which is braced by the uniform strut CD weighing 80 lbs and AE weighing 40 lbs. Determine the components of the pin pressure at C.
Show clear and complete solution. Show fbd. The rigid, homogeneous slab weighing 600 kN is supported by three rods of identical material and cross section. Before the slab was attached, the lower ends of the rods were at the same level. Compute the axial force in each rod.
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
Cansider the pipe shown in (Figure 1). The forces F = 250 N. F = 400 N and F = 600 N are paralel to the , y and z axes, respectively Part A Determine the z y and z components of reaction at the fixed support A using scalar notation Express your answers using three significant figures separated by commas VAE t vec Az. Ay. Az= Submit Request Answer Part B Determine the z, y and z components of moment of reaction at the foxed support A using scalar notation. Express your answers using three significant figures separated by commas. VAE vec (MA). (MA)y. (M,); = N.m Figure Submit Request Answer Provide Feedback 1 m 0.75 m 0.75 m
Given: Crane structure as shown. Find: Forces 600 and FBD's for cables A- Вoom B and A-E, boom DEF `F 375 and post AFC. 1800 1650 34.0 kN Dimensions in millimeters B 900 mm
The homogeneous AB beam weighs 400 lbs. For each support condition in (a) a (d), plot the DCL of the beam and determine the number of unknowns.
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal