Concept explainers
Fiberglass is a popular, economical, and fairly effective building insulation. It consists of fine glass fibers—often including recycled glass—formed loosely into rectangular slabs or rolled into blankets (Fig. 16.18). One side is often faced with heavy paper or aluminum foil. Fiberglass insulation comes in thicknesses compatible with common building materials—for example, 3.5 inch and 6 inch for wood-framed walls. Standard 6-inch fiberglass has an R-factor of 19.
Want to see the full answer?
Check out a sample textbook solutionChapter 16 Solutions
Essential University Physics: Volume 1 (3rd Edition)
Additional Science Textbook Solutions
University Physics Volume 2
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
An Introduction to Thermal Physics
Conceptual Physics (12th Edition)
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
- The vapor pressure is the pressure of the vapor phase of a substance when it is in equilibrium with the solid or liquid phase of the substance. The relative humidity is the partial pressure of water vapor in the air divided by the vapor pressure of water at that same temperature, expressed as a percentage. The air is saturated when the humidity is 100%. (a) The vapor pressure of water at 20.0°C is 2.34 × 10³ Pa. If the air temperature is 20.0°C and the relative humidity is 60%, what is the partial pressure of water vapor in the atmosphere (that is, the pressure due to water vapor alone)?arrow_forwardJill takes in 0.0140 mol of air in a single breath. The air is taken in at 20.0°C and exhaled at 35.0°C. Her respiration rate is (1.30x10^1) breaths per minute. At what average rate does heat leave her body due to the temperature increase of the air? Provide your answer to three significant figures. HINT: Use the molar specific heat at constant volume to find the heat loss, where Cv = 5R/2 (for an ideal diatomic gas).arrow_forwardAn engineer is designing a wire using an unknown material that will carry large amounts of electricity. The resistive heating of a 50.28 g wire is expected to add 560 J of heat energy during a 17-minute operating cycle. What is the temperature increase of the wire? You may use the following information about the unknown material to answer the question: Specific Heat = 0.313 J g-1 °C-1 Density = 7.98 g/cm3 Coefficient Thermal Expansion = 6.7 µm m-1 K-1arrow_forward
- The enthalpy of a system is given by the equation H=U+PV where U is the internal energy, P=pressure, and V=volume. In addition, the internal energy, U=Q+W where Q is the heat and W is the work. Suppose we want to find the rate of change in the enthalpy at constant pressure of 1.75 atm, what is the value when heat is absorbed by the system at a rate of 55 J/s and work is done by the system at a rate of 200 J/s when the change of volume is rated at 76 x 10^-5 m^3/s? 1. What is the change in heat with respect to time?2. What is the change in internal energy of the system with respect to time?3. What is the change in enthalpy of the system with respect to time?arrow_forwardTotal lung capacity of a typical adult is approximately 5.0 L. Approximately 20% of the air is oxygen. At sea level and at an average body temperature of 37°C, how many moles of oxygen do the lungs contain at the end of an inhalation?arrow_forwardA rod made of glass has a circular cross section with a diameter of 0.1200 m at a temperature of 20 degrees celsius. An aluminum ring has a diameter of 0.1196 m at a temperature of 20 degrees celsius. The coefficients of thermal expansion for glass and aluminum are 9.0 x 10-6 1/K and 24.0 x 10-6 1/K, respectively. At what temperature will the aluminum ring be able to slip over the glass rod? Between 225 and 250 degrees celsius Between 175 and 200 degrees celsius Between 100 and 125 degrees celsius Higher than 300 degrees celsius Between 250 and 275 degrees celsius Between 125 and 150 degrees celsius Between 275 and 300 degrees celsius Between 150 and 200 degrees celsius O Between 200 and 225 degrees celsiusarrow_forward
- Note: Round off your answer to the nearest whole number. Input the numerical value only. Problem. A composite wire to be used as an integral component of a switch in an electrical device is composed of wire A and wire B. The wire has effective linear expansion coefficient of 0.000021 per Celsius-degree. What percentage of the total length of the composite wire is wire B? The linear expansion coefficient of wire A is 0.000012 per Celsius-degree. The linear expansion coefficient of wire B is 0.000038 per Celsius-degree. Activate Windows Go to Settings to activate Windows Question 3 of 4arrow_forwardA certain car has 14 L of liquid coolant circulating at a temperature of 95 degrees Celsius through the engine’s cooling system. Assume that, in this normal condition, the coolant completely fills the 3.5 L volume of the aluminum radiator and the 10.5 L internal cavities within the aluminum engine. When a car overheats, the radiator, engine, and coolant expand and a small reservoir connected to the radiator catches any resultant coolant overflow. Estimate how much coolant overflows to the reservoir if the system goes from 95 degrees Celsius to 106 degrees Celsius. Model the radiator and engine as hollow shells of aluminum. The coefficient of volume expansion for coolant is 410x10^-6 degrees Celsiusarrow_forwardAt winter design conditions, a house is projected to lose heat at a rate of 60,000 Btu/h. The internal heat gain from people, lights, and appliances is estimated to be 6000 Btu/h. If this house is to be heated by electric resistance heaters, determine the required rated power of these heaters in kW to maintain the house at constant temperature.arrow_forward
- The specific heat of water is 4186 J/kg c°. How much does the internal energy of 200 g of water change as it is heated from 20°c to 30°c? Assume the volume is constant.arrow_forward11.6arrow_forwardA steel rod with a cross-sectional area of 0.20 in² is stretched between two fixed points. The tensile load at 65°F is 1250 lb. What will be the stress at 0°F? At what temperature will the stress be zero? Assume a = 6.5×106 in / (in-°F) and E = 29 × 10° psi.arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning