EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 16, Problem 70SDP
Obtain an aluminum beverage can and slit it in half lengthwise with a pair of tin snips. Using a micrometer, measure the thickness of the can bottom and the wall. Estimate the thickness reductions in ironing and the diameter of the original blank.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Comparing the processes of tube drawing and tube sinking:
a
tube sinking use a mandrel
b
tube sinking preciously controls the inside diameter
c
tube drawing uses a mandrel
d
tube drawing is used with thick walled tubes
What is the optimal thickness of a plate sheet that can be punched
out if the design stress is about 200 psi, and a punching force of
60,000 lbs. with a factor of safety of 5, if the puncher's diameter is
2-in.?
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that
has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is
12.0 mm.
Make a rough sketch, define the geometries to be used and determine
a. The punch and die size for the blanking operation
b. The punch and die size for the punching operation
c. The force required performing the blanking and punching operation simultaneously.
The aluminum has a tensile strength = 300 MPa.
Chapter 16 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 16 - How does sheet-metal forming differ from rolling,...Ch. 16 - What causes burrs? How can they be reduced or...Ch. 16 - Prob. 3RQCh. 16 - Describe the difference between compound,...Ch. 16 - Describe the characteristics of sheet metals that...Ch. 16 - Describe the features of forming-limit diagrams...Ch. 16 - List the properties of materials that influence...Ch. 16 - Give one specific application for each of the...Ch. 16 - Why do tubes buckle when bent? What is the effect...Ch. 16 - Define normal anisotropy, and explain why it is...
Ch. 16 - Describe earing and why it occurs.Ch. 16 - What are the advantages of rubber forming? Which...Ch. 16 - Explain the difference between deep drawing and...Ch. 16 - How is roll forming fundamentally different from...Ch. 16 - What is nesting? What is its significance?Ch. 16 - Describe the differences between compound,...Ch. 16 - What is microforming?Ch. 16 - Explain the advantages of superplastic forming.Ch. 16 - What is hot stamping? For what materials is it...Ch. 16 - What is springback? What is negative springback?Ch. 16 - Explain the differences that you have observed...Ch. 16 - Take any three topics from Chapter 2, and, with...Ch. 16 - Do the same as for Problem 16.22, but for Chapter...Ch. 16 - Identify the material and process variables that...Ch. 16 - Explain why springback in bending depends on yield...Ch. 16 - Explain why cupping tests may not predict well the...Ch. 16 - Identify the factors that influence the...Ch. 16 - Why are the beads in Fig. 16.36b placed in those...Ch. 16 - A general rule for dimensional relationships for...Ch. 16 - Section 16.2 stated that the punch stripping force...Ch. 16 - Is it possible to have ironing take place in an...Ch. 16 - Note the roughness of the periphery of the flanged...Ch. 16 - What recommendations would you make in order to...Ch. 16 - It has been stated that the quality of the sheared...Ch. 16 - Give several specific examples from this chapter...Ch. 16 - As you can see, some of the operations described...Ch. 16 - Through changes in clamping or die design, it is...Ch. 16 - How would you produce the part shown in Fig....Ch. 16 - It has been stated that the thicker the sheet...Ch. 16 - Prob. 41QTPCh. 16 - Calculate the value of R in Problem 16.41. Will...Ch. 16 - Estimate the limiting drawing ratio for the...Ch. 16 - Using Eq. (16.15) and the K value for TNT, plot...Ch. 16 - Section 16.5 states that the k values in bend...Ch. 16 - For explosive forming, calculate the peak pressure...Ch. 16 - Measure the respective areas of the solid outlines...Ch. 16 - Plot Eq. (16.6) in terms of the elastic modulus,...Ch. 16 - What is the minimum bend radius for a 1.0-mm-thick...Ch. 16 - Survey the technical literature and explain the...Ch. 16 - Using the data in Table 16.3 and referring to Eq....Ch. 16 - What is the force required to punch a square hole...Ch. 16 - In Case Study 16.2, it was stated that the reason...Ch. 16 - A cup is being drawn from a sheet metal that has a...Ch. 16 - Prob. 55QTPCh. 16 - Figure P16.57 shows a parabolic profile that will...Ch. 16 - Prob. 59SDPCh. 16 - Consider several shapes to be blanked from a large...Ch. 16 - Prob. 61SDPCh. 16 - Many axisymmetric missile bodies are made by...Ch. 16 - Metal cans are either two-piece (in which the...Ch. 16 - The design shown in Fig. P16.65 is proposed for a...Ch. 16 - Suggest consumer-product designs that could...Ch. 16 - How would you produce the part shown in Fig. 16.44...Ch. 16 - Using a ball-peen hammer, strike the surface of...Ch. 16 - Inspect a common paper punch and observe the shape...Ch. 16 - Obtain an aluminum beverage can and slit it in...Ch. 16 - Prob. 71SDPCh. 16 - Prob. 73SDPCh. 16 - On the basis of experiments, it has been suggested...Ch. 16 - Design a box that will contain a 4-in. 6-in. ...Ch. 16 - Repeat Problem 16.77, but design the box from a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Answer the questions based from the resultarrow_forwardA compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 3.50 mm thick. The outside diameter of the washer is 50.0 mm and the inside diameter is 15.0 mm. Determine (a) the punch and die sizes for the blanking operation, and (b) the punch and die sizes for the punching operation Vallue for allowance = 0.060arrow_forwardA circular shape blank will be cut of 105 mm diameter from a strip of 3.3 mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine The appropriate punch diameter. Blanking force. Blanking force when the blade angle is 5.5arrow_forward
- A compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 3.50 mm thick. The outside diameter of the washer is 50.0 mm and the inside diameter is 15.0 mm. Determine the punch and die sizes for the punching operation. TABLE 20.1 Clearance allowance value for three sheet-metal groups. Metal Group A. 1100S and 5052S aluminum alloys, all tempers 2024ST and 6061ST aluminum alloys; brass, all tempers; soft cold- 0.045 0.060 rolled steel, soft stainless steel Cold-rolled steel, half hard; stainless steel, half-hard and full-hard 0.075 Select one: a. 18.42 mm b. 20.42 mm c. 19.42 mm d. 15.42 mmarrow_forwardFind the process tolerance for blanking o 40 piece from 2 mm thick mild steel Sheet. (Take minimum die clearance of 2% per side)arrow_forwardA compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking, Take: Ac-0.06arrow_forward
- Correct and complete solution please don't copyarrow_forwardA worker in a large welding and steel fabrication shop asked his employer if he could make a trailer hitch for his pickup truck after hours if he paid the shop for the material used. His employer gave him permission. That evening, the worker searched among the many racks of various kinds of steel bars for the one suitable for his job. He selected a 1/2 by 2 inch HR bar and sawed off the pieces he needed. He drilled holes, heated areas red hot to bend them, then quenched them in water. He welded the parts together and assembled the hitch on his truck. When he got home and he lifted the tongue of his trailer over the hitch and dropped it in place, to his great surprise, the hitch broke off and fell to the ground. What had he done wrong?arrow_forwardWrite a detail note on “Tube Drawing with Mandrels”.arrow_forward
- A compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 4.50 mm thick. The outside diameter of the washer is 60.0 mm and the inside diameter is 25.0 mm. Determine the punch and die sizes for the blanking operation. Determine the force required to perform the blanking and punching operation, assuming that the punches are staggered so that punching occurs first, then blanking. The aluminum sheet metal has a tensile strength = 310 MPa. Consider a clearance allowance value of 0.060.arrow_forwardThe Sleeve Bearing Problem A machinist had pressed a new prelubricated, porous sintered bronze bearing in an electric motor. The rotor shaft would not fit into the searing. Measuring the bore, the machinist discovered that it was a few thousandths of an inch undersized. He removed it, put it in a lathe, and bored out the excess material. The bearing was pressed in again, the motor assembled, and put into use. A few days later the motor was back in the shop with the bearing burned out. What had happened to this prelubricated, sintered bearing to cause the failure.arrow_forwardA figure shown below is to be blanking through a blanking die The material is 4mm thick stainless steel (half hard) with Ac =0.075. Determine the dimensions of the blanking punch and the die openingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Relationship Between Elastic Constants and Connecting Equations; Author: Engineers Academy;https://www.youtube.com/watch?v=whW5PnM7Pug;License: Standard Youtube License