EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 15, Problem 28QLP
What is the purpose of the land in a drawing die? Is there a limit to the size of the land that should be used? Explain.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
1. Derive an expression for the reduction r in drawing as a function of drawing ratio DR.2. A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its insidediameter = 100 mm. The sheet-metal thickness = 2 mm. If the blank diameter = 225 mm, determine(a) drawing ratio, (b) reduction, and (c) thickness-to-diameter ratio. (d) Does the operation seem feasible?3. A drawing operation is used to form a cylindrical cup with inside diameter = 65 mm and height =50mm. The starting blank size = 140 mm and the stock thickness = 2.8mm. determine (a) drawing forceand (b) holding force, given that the tensile strength of the sheet metal (low-carbon steel) = 350 MPa andyield strength = 190 MPa. The die corner radius = 6 mm. Based on these data, is the operation feasible?
Explain briefly the relationship between the load-stroke in open die forging as illustrated in the figures bellow. Take in consideration the effect of coefficient of friction.
Correct and complete solution please don't copy
Chapter 15 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 15 - How does extrusion differ from rolling and...Ch. 15 - Explain the difference between extrusion and...Ch. 15 - What is a spider die? What is it used for?Ch. 15 - Why are wires sometimes drawn in bundles?Ch. 15 - What is a dead-metal zone?Ch. 15 - Define the terms (a) cladding, (b) dummy block,...Ch. 15 - Why is glass a good lubricant in hot extrusion?Ch. 15 - What types of defects may occur in (a) extrusion...Ch. 15 - Describe the difference between direct and reverse...Ch. 15 - What is land? What is its function in a die?
Ch. 15 - How are tubes extruded? Can they also be drawn?...Ch. 15 - Prob. 12RQCh. 15 - What is the difference between piping and...Ch. 15 - What is impact extrusion?Ch. 15 - What is the pipe defect in extrusion?Ch. 15 - List the similarities and differences between...Ch. 15 - Explain why extrusion is a batch, or...Ch. 15 - The extrusion ratio, die geometry, extrusion...Ch. 15 - Explain why cold extrusion is an important...Ch. 15 - What is the function of a stripper plate in impact...Ch. 15 - Explain the different ways by which changing the...Ch. 15 - Glass is a good lubricant in hot extrusion. Would...Ch. 15 - How would you go about avoiding center-cracking...Ch. 15 - Table 15.1 gives temperature ranges for extruding...Ch. 15 - Will the force in direct extrusion vary as the...Ch. 15 - Comment on the significance of metal flow patterns...Ch. 15 - In which applications could you use the type of...Ch. 15 - What is the purpose of the land in a drawing die?...Ch. 15 - Can spur gears be made by (a) drawing and (b)...Ch. 15 - How would you prepare the end of a wire in order...Ch. 15 - What is the purpose of a dummy block in extrusion?...Ch. 15 - Describe your observations concerning Fig. 15.9.Ch. 15 - Occasionally, steel wire drawing will take place...Ch. 15 - Explain the advantages of bundle drawing.Ch. 15 - Under what circumstances would backward extrusion...Ch. 15 - Why is lubrication detrimental in extrusion with a...Ch. 15 - In hydrostatic extrusion, complex seals are used...Ch. 15 - Describe the purpose of a container liner in...Ch. 15 - Estimate the force required in extruding 7030...Ch. 15 - Assuming an ideal drawing process, what is the...Ch. 15 - Prob. 41QTPCh. 15 - Calculate the extrusion force for a round billet...Ch. 15 - Prob. 43QTPCh. 15 - A round wire made of a perfectly plastic material...Ch. 15 - Assume that the summary to this chapter is...Ch. 15 - Prob. 47SDPCh. 15 - Figure 15.2 shows examples of discrete parts that...Ch. 15 - The parts shown in Fig. 15.2 are economically...Ch. 15 - Survey the technical literature, and explain how...Ch. 15 - Prob. 51SDPCh. 15 - List the processes that are suitable for producing...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Differentiate ISOMETRIC DRAWING to OBLIQUE DRAWING.arrow_forward6. You have been consulted to design a draw die system for a wire production facility. The starting diameter is 3.0 mm and velocity is 5 m/s. The final diameter is 1.55 mm. Area reduction in drawing (r) is guided by the formula A, – Af Ao where A,=original area of work and AFfinal area. The upper limits for r are 0.50 for single-draft bar drawing and 0.30 for multiple-draft wire drawing respectively. Sketch the draw die system with all applicable system values/measurements incorporated. Assume no changes in volume due to forming.arrow_forward4) In the deep drawing of cups, blanks show a tendency to wrinkle up around the periphery (flange). The most likely cause and remedy of the phenomenon are respectively: Buckling due to circumferential compression; Increase blank holder pressure. High blank holder pressure and high friction; Reduce blank holder pressure and apply lubricant. High temperature causing an increase in circumferential length; Apply coolant to blank. Buckling due to circumferential compression; decrease blank holder pressure.arrow_forward
- I need the answer as soon as possiblearrow_forwardIt is proposed to use an axisymmetric drawing operation to reduce the diameter of a cylindrical rod of steel from Do to Do/4. If the steel behaves like a perfectly-plastic material, and there is no redundant deformation or friction in the process, what is the minimum number of drawing stages needed to obtain this reduction?arrow_forward3) Which of the below statements is/are correct regarding deep drawing process? i. If the clearance between the punch and the die is less than the thickness produced by free thickening, the metal in these regions will be squeezed, or ironed. ii. The force on the punch required to produce a cup is the summation of the ideal force of deformation, the frictional forces, and the force required to produce ironing (if present). i only ii only Both i and ii None of the abovearrow_forward
- 4) What is forging? One way to classify forging operations is by the degree to which the work is constrained in the die. By this classification, explain the three basic types. (with using figures also).arrow_forwardA drawing operation is used to form a cylindrical cup with inside diameter of 75 mm and height of 50 mm. The starting blank size is 140 mm and the stock thickness is 2.4 mm. Based on the data, is the operation feasible?arrow_forwardThe quantity of work that can be done in the die may be used as a defining feature of forging processes. Please identify the following three broad classes that this sorting generates.arrow_forward
- In a two stage wire drawing operation, the fractional reduction (ratio of change in cross- sectional area to initial cross-section area) in the first stage is 0.4. The fractional reduction in the second stage is 0.3. determine the overall fraction of the operation.arrow_forwardplease solve all questonarrow_forwardPlease answer all partsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License