Explanation Express the density of ambient air. ρ ambient = P 0 R T 0 (I) Here, atmospheric pressure is P 0 , universal gas constant of air is R and surrounding temperature is T 0 . Express mass flow rate of air. m ˙ air = ρ ambient ν room ACH = ρ ambient ( l b h ) ACH (II) Here, air changes per hour is ACH , volume of room is ν room and length, width and height of room is l b h respectively. Express sensible heat load of the room. Q ˙ infiltration,sensible = m ˙ air c p ( T ambient − T room ) (III) Here, specific heat at constant pressure is c p , room temperature is T room and ambient temperature is T ambient . Express latent heat load of the room. Q ˙ infiltration,latent = m ˙ air ( ω ambient − ω room ) h f g @24°C (IV) Here, humidity ratio of room is ω room , ambient humidity ratio is ω ambient and latent heat of vaporization at temperature of 24°C is h f g @24°C . Express total heat load of the room. Q ˙ infiltration,total = Q ˙ infiltration,sensible + Q ˙ infiltration,latent (V) Conclusion: Take the atmospheric pressure as 101 .325 kPa . Refer Table A-2, “ideal-gas specific heats of various common gases”, and write the universal gas constant and specific heat at constant pressure of air. R = 0.2870 kPa ⋅ m 3 / kg ⋅ K c p = 1.005 kJ / kg ⋅ ° C Refer Table A-4, “Saturated water-temperature table”, and write the specific enthalpy evaporation or latent heat of vaporization at temperature of 24°C . h f g @24°C ≃ h f g @25°C = 2441.7 kJ / kg Here, latent heat of vaporization at temperature of 25°C is h f g @25°C . Refer Figure A-31, “Psychrometric chart at 1 atm total pressure”, and write the ambient humidity ratio corresponding to ambient temperature of 32°C and relative humidity of 35 % . ω ambient = 0.01039 kg / kg dry air Refer Figure A-31, “Psychrometric chart at 1 atm total pressure”, and write the humidity ratio of room corresponding to ambient temperature of 24°C and relative humidity of 55 % . ω room = 0.01024 kg / kg dry air Substitute 101 .325 kPa for P 0 , 0.2870 kPa ⋅ m 3 / kg ⋅ K for R and 32°C for T 0 in Equation (I). ρ ambient = 101 .325 kPa ( 0.2870 kPa ⋅ m 3 / kg ⋅ K ) ( 32°C ) = 101 .325 kPa ( 0.2870 kPa ⋅ m 3 / kg ⋅ K ) ( 32 + 273 ) K = 101 .325 kPa ( 0

9th Edition

ISBN: 9781266657610

Author: CENGEL

Publisher: MCG CUSTOM

See similar textbooks

Videos

Question

Chapter 14.7, Problem 59P

To determine

Sensible, latent, and total infiltration heat load of a building at sea level.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 14.7, Problem 58P

Chapter 14.7, Problem 60P

Students have asked these similar questions

The 150-lb skater passes point A with a speed of 6 ft/s. (Figure 1) Determine his speed when he reaches point B. Neglect friction. Determine the normal force exerted on him by the track at this point. 25 ft B = 4x A 20 ft x

A virtual experiment is designed to determine the effect of friction on the timing and speed of packages being delivered to a conveyor belt and the normal force applied to the tube. A package is held and then let go at the edge of a circular shaped tube of radius R = 5m. The particle at the bottom will transfer to the conveyor belt, as shown below. Run the simulations for μ = 0, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6 and determine the time and speed at which the package is delivered to the conveyor belt. In addition, determine the maximum normal force and its location along the path as measured by angle 0. Submit in hardcopy form: (0) Free Body Diagram, equations underneath, derivations (a) Your MATLAB mfile (b) A table listing the values in 5 columns: μ, T (time of transfer), V (speed of transfer), 0 (angle of max N), Nmax (max N) (c) Based on your results, explain in one sentence what you think will happen to the package if the friction is increased even further, e.g. μ = 0.8. NOTE: The ODE is…

Patm = 1 bar Piston m = 50 kg 5 g of Air T₁ = 600 K P₁ = 3 bar Stops A 9.75 x 10-3 m² FIGURE P3.88

Chapter 14 Solutions

THERMODYNAMICS (LL)-W/ACCESS >CUSTOM<

Ch. 14.7 - What is the difference between dry air and...Ch. 14.7 - What is vapor pressure?Ch. 14.7 - What is the difference between the specific...Ch. 14.7 - Can the water vapor in air be treated as an ideal...Ch. 14.7 - Explain how vapor pressure of the ambient air is...Ch. 14.7 - Is the relative humidity of saturated air...Ch. 14.7 - Moist air is passed through a cooling section...Ch. 14.7 - How will (a) the specific humidity and (b) the...Ch. 14.7 - Prob. 9P Ch. 14.7 - Consider a tank that contains moist air at 3 atm...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Sensible, latent, and total infiltration heat load of a building at sea level.

Solution Summary: The author explains the sensible, latent, and total infiltration heat load of a building at sea level.

Videos

Sensible, latent, and total infiltration heat load of a building at sea level.

Want to see the full answer?

Chapter 14 Solutions