The local atmospheric pressure in Denver, Colorado (elevation 1610 m) is 83.4 kPa. Air at this pressure and at 25’C flows with a velocity of 9 m/s over a 2.5-rn 5-rn flat plate. Determine the drag force acting on the top surface of the plate if the air flows parallel to the (a) 5-rn-long side and (b) the 2.5-m-long side.
(a)
The drag force acting on the top surface of the plate when the air flows parallel to the 5 m long side.
Answer to Problem 48P
Explanation of Solution
Given information:
Concept used:
Calculation:
The gas constant is,
For the given temperature,
Conclusion:
The drag force acting on the top surface of the plate when the air flows parallel to the 5 m long side is
(b)
The drag force acting on the top surface of the plate when the air flows parallel to the 2.5 m long side.
Answer to Problem 48P
Explanation of Solution
Given information:
Concept used:
Calculation:
The gas constant is,
For the given temperature,
Conclusion:
The drag force acting on the top surface of the plate when the air flows parallel to the 2.5 m long side is
Want to see more full solutions like this?
Chapter 11 Solutions
Fluid Mechanics: Fundamentals and Applications
- Consider 0.8-cm-diameter hail that is falling freely in atmospheric air at 1 atm and 5°C. Determine the terminal velocity of the hail. Take the density of hail to be 910 kg/m3. Take the density and kinematic viscosity of air at 1 atm and 5°C as ρ = 1.269 kg/m3 and v = 1.382 × 10–5 m2/s. The figure for the average drag coefficient for cross-flow over a smooth circular cylinder and a smooth sphere is given below. Find the terminal velocity of the hail:arrow_forwardThe jet plane in Fig. 6–19a is in level flight with a constant speed of 140 m/s. Each of its two turbojet engines burns fuel at a rate of 3 kg/s. Air, at a temperature of 15°C, enters the intake, which has a cross- sectional area of 0.15 m². If the exhaust has a velocity of 700 m/s, mea- sured relative to the plane, determine the drag acting on the plane. W 140 m/s FD O O O OO O O Oo O (a) (b)arrow_forwardA circular sign has a diameter of 50 cm and is subjected to normal winds up to 150 km/h at 10°C and 100 kPa. Determine the drag force acting on the sign. Also determine the bending moment at the bottom of its pole whose height from the ground to the bottom of the sign is 1.5 m. Disregard the drag on the pole.arrow_forward
- During major windstorms, high vehicles such as RVs and semis may be thrown off the road and boxcars off their tracks, especially when they are empty and in open areas. Consider a 5000-kg semi that is 9 m long, 2.5 m high, and 2 m wide. The distance between the bottom of the truck and the road is 0.75 m. Now the truck is exposed to winds from its side surface. Determine the wind velocity that will tip the truck over to its side. Take the air density to be 1.1 kg/m3 and assume the weight to be uniformly distributed.arrow_forwardConsider laminar flow of a fluid over a flat plate. Now the free-stream velocity of the fluid is tripled. Determine the change in the drag force on the plate. Assume the flow to remain laminar.arrow_forwardA 2.4-in-diameter smooth ball rotating at 500 rpm is dropped in a water stream at 60°F flowing at 4 ft/s. Determine the lift and the drag force acting on the ball when it is first dropped in the water.arrow_forward
- A circular sign has a diameter of 50 cm and is subjected to normal winds up to 150 km/h at 10°C and 100 kPa. Determine the drag force acting on the sign. Also determine the bending moment at the bottom of its pole whose height from the ground to the bottom of the sign is 1.5 m. Disregard the drag on the pole.arrow_forwardAir is flowing past a spherical ball. Is the lift exerted on the ball zero or nonzero? Answer the same question if the ball is spinning.arrow_forwardA submarine can be treated as an ellipsoid with a diameter of 5 m and a length of 25 m. The submarine is cruising horizontally and steadily at 65 km/h in seawater (p = 1025 kg/m³.p = 0.00108 Ns/m2). Determine: The Reynolds number for the submarine and state whether the flow is in the laminar or turbulent regime. ii. The drag force on the submarine. iii. The power required to overcome the drag force. To surface, a total lift force of 1000 kN is required from a pair of NACA 0012 hydroplanes. Each hydroplane has a chord length of 1 m and a iv. span of 3 m. What angle of attack should be used?arrow_forward
- The passenger compartment of a minivan traveling at 50 mi/h in ambient air at 1 atm and 80°F is modeled as a 4.5-ft-high, 6-ft-wide, and 11-ft-long rectangular box. The airflow over the exterior surfaces is assumed to be turbulent because of the intense vibrations involved. Determine the drag force acting on the top and the two side surfaces of the van and the power required to overcome it.arrow_forwardAn automotive engine can be approximated as a 0.4-m-high, 0.60-m-wide, and 0.7-m-long rectangular block. The ambient air is at 1 atm and 15°C. Determine the drag force acting on the bottom surface of the engine block as the car travels at a velocity of 120 km/h. Assume the flow to be turbulent over the entire surface because of the constant agitation of the engine blockarrow_forwardThe passenger compartment of a minivan traveling at 50 mi/h in ambient air at 1 atm and 80°F is modeled as a 4.5-ft-high, 6-ft-wide, and 11-ft-long rectangular box. The airflow over the exterior surfaces is assumed to be turbulent because of the intense vibrations involved. Determine the drag force acting on the top and the two side surfaces of the van and the power required to overcome it.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY