You wish to detect only the presence of the codes 1010, 1100, 0001, and 1011. An active- HIGH output is required to indicate their presence. Prepare the minimum decoding logic with a single output that will indicate when any one of these codes is on the inputs. For any other code, the output must be LOW. Also implement the decoding Logic using 74HC151 (8-input Data Selector/ multiplexer).

You wish to detect only the presence of the codes 1010, 1100, 0001, and 1011. An active- HIGH output is required to indicate their presence. Prepare the minimum decoding logic with a single output that will indicate when any one of these codes is on the inputs. For any other code, the output must be LOW. Also implement the decoding Logic using 74HC151 (8-input Data Selector/ multiplexer).

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

In IC 74153,the input at pin number 14 is Options A-Connected to ground B-Connected to power/VCC C-Connected to LOGIC State D-Connected to LOGIC Probe
program using emu 8086
1- What does the VOH parameter of a logic IC refer to? a) The highest permissible output voltage. b) The lowest output voltage recognized as logic 1. c) The highest output voltage recognized as logic 1. d) The highest output voltage recognized as logic 0. 2- Which of the following refers to the noise margin of a logic gate? a) The difference between VIH and VOL b) The difference between VOH and VOL c) The difference between VOH and VIH d) The difference between VIH and VIL 3- How many 74LS00 NAND gate inputs can be driven by a 74LS00 NAND gate outputs Refer to data sheet of 74LS00, the maximum values of IOH = 0.4 mA, IOL = 8 mA, IH = 20 μA, and IL = 0.4 mA. 4- The data sheet of a quad two-input NAND gate specifies the following parameters: IOH (max.) 0.4 mA, VOH (min.) 2.7 V, VIH (min.) =2V, VIL (max.) 0.8 V, VOL (max.) 0.4 V, IOL (max.) 8 mA, IL (max.)=0.4 mA, IIH (max.)-20µA, ICCH (max.) 1.6 mA, ICCL (max.) 4.4 mA, tpLH =pHL=15 ns and a supply voltage range of 5…
Using the emu8086 program, I need to solve two points and explain the difference in the solutions between them. Question: Compute the physical address for the specified each of the following instructions. The register contents and as follows: (CS)=0A00H, (DS)=0B00Н, (DI)=00BOH, (BP)=00EAH and BX-2500H. 1) Destination operand of the instruction 2) Source operand of the instruction (IP)-0000H, (SS)=0D00H, LIST=00FOH, MOV LIST [BP+DI], AX MOV CL, [BX+200H] operand in variable are (SI)=OFFOH, AX=4020H,
Design and draw a 3 bit Gray code synchronous counter with the state diagram shown below [14 marks] State diagram for a 3-bit Gray code counter
A multiplexer a.Takes a single data input and routes it to one of several outputs b.Selects from many data sources c.converts a binary code input to a single output d.converts a single input to a binary code
None
Please help me, solve this question.
1What will be the state of a MOD64 counter after 90 input pulses if the starting state=000000?A.100100B.011010C.010110D.011100 2.A MOD 32 counter is holding the count 101112. What will the count be after 31 clock pulses?A.10100B.10010C.10000D.10110
Given the 74LS147 Encoder TINKHK167006 Logic Symbol 56679AWN 74LS147 (a) What would be output if input 1,2, and 7 were activated simultaneously. (b) Sketch the wiring diagram for input 1,5, and 8 with push button as user input.
program to emu8086
need handwritten with explanation Clear