Design a digital logic-based smart lighting control system that optimizes energy efficiency, responds to environmental and user inputs, and scales to accommodate multiple rooms. The system must control the lights in each room based on room occupancy, ambient light levels, manual overrides, and a security mode that activates alarms during unoccupied periods. Your challenge is to design the system using only combinational and sequential logic components without relying on microcontrollers or programming.

Design a digital logic-based smart lighting control system that optimizes energy efficiency, responds to environmental and user inputs, and scales to accommodate multiple rooms. The system must control the lights in each room based on room occupancy, ambient light levels, manual overrides, and a security mode that activates alarms during unoccupied periods. Your challenge is to design the system using only combinational and sequential logic components without relying on microcontrollers or programming.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

Explain and draw a 7490 chip in a circuit of your own design. I want the actual chips drawn with the symbols inside, then a wiring diagram showing the interconnections. Power source and A, B, C, and/or D inputs may be added in the form of either buttons or switches.
Solve correct please
Question: Consider you are asked to design a digital system that controls an electric motor “M". Motor is turned on when logic 0 is applied and turns off when logic 1 is applied. Two identical photo sensors, “S1" and "S2" produce logic 1 when light falls on them and provide logic 0 when light does not fall on them. Motor is to be controlled in such a way when light falls on both sensors, motor turns on. When light falls on S1 only, motor turns on. When light falls on S2 only motor turns off. Motor turns off when both sensors do not receive any light. Perform the following tasks: A. List the truth table. B. Write down the output equation. C. Draw the circuit diagram. D. Implement on Proteus (paste screen shot of implemented circuit).
As a general rule, for programmable logic controllers, coils can be connected in a series. True or Flase
Circuit Logic. Match each statement to the proper circuit. All circuits have been drawn with a light (L) to represent the load, whether it is a motor, bell, or any other kind of load. In addition, each switch is illustrated as a pushbutton whether it is a maintained switch, momentary switch, pushbutton, switch-on target, or any other type of switch. from electrical motor controls for integrated systems workbook 2014 chapter 5
Explain and draw an NPN transistor chip in a circuit of your own design. I want the actual chips drawn with the symbols inside, then a wiring diagram showing the interconnections. Power source and A, B, C, and/or D inputs may be added in the form of either buttons or switches.
Arrange a circuit to implement the following logic: In a production system, conveyors are used to deliver workpieces from one place to another. The START (with memory) and STOP pushbuttons are used to activate (stand-by) and disable the system. In the stand-by condition, the conveyor motor will turn on if an object touches the first limit switch and will turn off if the object touches the second limit switch. The red-light flashes to indicate the conveyor is moving. If the conveyor is not moving, the green light will be on. Draw ladder diagrams and wiring diagrams!
Study the ladder logic program in figure below and answer the questions that follows: a) What type of timer has been programmed? Explain the timers function in detail with suitable graph: b) What is the length of the time-delay period? c) What is the value of the accumulated time when power is first applied? d) When does the timer start timing? e) When does the timer stop timing and reset itself? Input LS1 Outputs L1 TON L2 TIMER ON DELAY Timer Time base Preset KEN T4:0 LS1 ISOL A-o 1 10 KON) Accumulated SOL B- T4:0 SOL A DN T4:0 SOL B 3 DN T4:0 EN T4.0 EN
Draw a 2x1 multiplexer block diagram.Create the status table. Find the simplest form of circuit output with Karnaugh.Explain the circuit problem that may occur.What should be done to fix the problem?(NEED A NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE)
we are interested in an automatic garage gate system for a building. This system includes a gate that goes up or down, a motor to actuate the gate (pull, push) and sensors to collect information (gate open contact, gate closed contact). The sensors are all similar, each signaling to its controller that a contact has taken place. The user has a remote control to control with just two buttons: open, close. The operating principle of the system is as follows. Suppose the gate is closed. The user opens the gate by pressing the Open button on his remote control. He can stop opening by pressing the Open button again, the motor stops. Otherwise, the gate opens completely and triggers a Gate Open sensor which causes the motor to stop. Pressing the Close button causes the gate to close if it is open (partially or fully). The closing can be stopped by pressing the Close button again, the motor stops. Otherwise, the gate closes completely and triggers a Gate Closed sensor which causes the engine…
I have a 24 MHz fast 8051 microcontroller, by ATMEL. It has a machine cycle of 12 clocks. Iwould like to generate a time delay of 512 microseconds (µs = 10-6). Design your timerwithout using mode 1.1. Which Timer and what mode are you going to use?2. What is the delay count and the base number of your design?3. Configure and program the TMOD register according to your design. 4. Write the assembly code of your design to program the microcontroller and generatethe 512 µs delay!
please show all work and steps,kindly thank you.