Danny Mizhquiri CET-3615 Home Work #5 11/11/2024 Fall 2024 1. For this Open Loop Amplifier - Sketch and Label Vo(t) for each switch position: a. Switch "SI" connect to the (A) ground b. Switch "51" connect to (B) +2V. +Vcc (+5V) 4 S.Ov (a) 51 (A) V(-) N له 2 VCE) 3 (B) VI 2V + 5.0V 6 +9+ 5 741 1 -Voc (-5V) +6 V+5V. V(+) V(-) +4 +2 1 V(+) V(-) +Vcc Vo=+5V Vo V(+) 2 • t(ms) 3 4 -Vcc Vo=-5V -14- +5V RVO -6

Danny Mizhquiri CET-3615 Home Work #5 11/11/2024 Fall 2024 1. For this Open Loop Amplifier - Sketch and Label Vo(t) for each switch position: a. Switch "SI" connect to the (A) ground b. Switch "51" connect to (B) +2V. +Vcc (+5V) 4 S.Ov (a) 51 (A) V(-) N له 2 VCE) 3 (B) VI 2V + 5.0V 6 +9+ 5 741 1 -Voc (-5V) +6 V+5V. V(+) V(-) +4 +2 1 V(+) V(-) +Vcc Vo=+5V Vo V(+) 2 • t(ms) 3 4 -Vcc Vo=-5V -14- +5V RVO -6

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A differential op-amp circuit as shown below is used to implement a given linear voltage measuring functionV = f(V,). ouf Provide answers to questions 19 – 22. ww V. V; W R out R2 Ground
Vin -100m/100mV. 10kHz RI B10k RF 100k Vcc +12V U1 UA741 A RL 25k -12V Vee 1. What are the basic features of an OP-AMP? (6) 2. Basic op-amp connections include what? (10) 3. Simulate the circuit using Circuit maker and explain the different between A and B.
answer those questions (True and False).. Please answer all subpart I will like it please only true or false.. please all..
What must the voltage at the inverting input of the op-amp be? What is the voltage drop across Rin? What is the input current, iin, through Rin? What is the output voltage vout?
Q1 Design an operational-amplifier circuit using two inverting configurations to produce the output vo = +201 + 0.5v2 – 0.2v3 – 1v4. Choose feedback resistor Rf = 220kN for each amplifier. %3D | -
(a) An operational amplifier shown in Figure 1. Sketch the real circuit model of the amplifier. As a real op-amp it has the following specifications: Input resistance Output resistance Open-loop gain Rin=1MQ Ro=2002 Ao=100,000 190KQ Figure. 1
Hand Calculation: 1. For different configurations shown in Figure 1, perform approximate hand calculations assuming that the operational amplifier is ideal. In each case sketch the expected output waveform in Table I. Assume that the sine and triangular waves have amplitude of 1V, the square wave varies from 0 to 5V with 50% duty cycle, and frequency of all signals is set to 1kHz. 2. Redesign the integrator circuit so that when the input is sine wave with frequency 1kHz the output voltage will have same amplitude. Use C=0.1μF. 3. Redesign the differentiator circuit so that when the input is sine wave with frequency 1kHz the output voltage will have same amplitude. Use C=0.1μF.
An inverting operational amplifier circuit is manufactured from an op-amp, two resistors of values 4 kQ and 10 kO, and suitable power supplies. The input voltage is 3 volts DC. The output voltage is O -1.2 volts or -7.5 volts DC O 7.5 volts or 1.2 volts DC O 4.2 volts or -10.5 volts AC O 4 volts or 10 volts DC
+Vcc Vin VI Vo Vref VN -Vcc Ry RxL Figure Q.A2(e). Inverting Schmitt-trigger circuit. (ii) The operational-amplifier (op-amp) of the inverting Schmitt-trigger in Figure Q.A2(e) has saturation voltages of +Vsat = +11 V and -Vsat = -11 V. The voltage divider circuit has the relationship of Rx = 2RY with the value of RY being 100 kn. Using the relationships derived above: (a) Calculate the values of the upper threshold point (UTP or Vi*), lower threshold point (LTP or Vr). (b) Now, sketch the input-output characteristic of the inverting Schmitt- trigger. Clearly label axes, the threshold voltages and the saturation voltages in your sketch.
I need help with Op-amp. tnx
Using any number of Op-Amps, design multistage amplifier to amplify input Ac signal with 0.01V amplitude, the expected output voltage would have 4V amplitude. The input signal frequency = 10 KHz. Assume gain bandwidth product of Op-Amp = 1 MHz
3S Which of the followinh statements are true about an op-amp? a.op-amps have very high input impedance b.all of the statements c.op-amps have very low output impedance d.op-amps are very high gain DC amplifiers