■. Calculate the currents I, and I2 for the circuit shown in phasor form using currentdivider rule.XLI₁40I = 8A45°XcRWW12 Ω602

Step 1: Step 2: Step 3: Step 4:

Answered: ■. Calculate the currents I, and I2 for…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
Let's say you measure t1/2 to be 0.037 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? Answer in micro Farads.
What's 21 22 23
The current through a 15kohm resistor is given below, using Ohm’s Law to find the voltage, convert to polar form, complete the math, then convert back to the waveform at i1 = 3.5sin(2500t) mA and i2 = 2.3sin(200t – 60°) mA
Okay for Determine the mathematical expression for the voltage vC and the current iC for the discharge phase. I got Vc = 8e-t/0.2s V and iC = -4e-t/0.2mA But I need help with the last question Plot the waveforms of vC and iC for a period of time extending from 0to 2 s from when the switch was thrown into position 1.
Which methods can be used to estimate or calculate the maximum power point on an I-V curve?
how to measure ripple factor and peak input and peak output voltage for this circuits ?
A pure resistance of 50 ohms is in series with a pure capacitance of 100 microfarads. The series combination is connected across a 100 volt, 50 hz source. Find the a) impedance, b) phase angle, and c) equation of the current
If the resistors used for charging and discharging were the same, the charging anddischarging waveform would be ________.a. Symmetricalb. Nonsymmetrical
1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.
What is the net, coupling capacitance cm and lateral capacitance? Explain this circuit in a really basic way
A utility company plans to connected a total of 20uF of capacitance to a 7,200 volt line. To make this connection, four capacitors will be connected in series. What is the capacitance of each capacitor?

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

■. Calculate the currents I, and I2 for the circuit shown in phasor form using current divider rule. XL I₁ 40 I = 8A45° Xc R WW 12 Ω 602