Need a sol 12.2 A T1 line is used to carry traffic from a remote concentrator to a central office.How many 10 CCS subscribers can the concentrator system support at 0.5%blocking. Compare an infinite source analysis to a finite source analysis. As-sume blocked calls cleared.

Answered: Image /qna-images/answer/c63ed803-27c4-430a-9743-5d39194b449d.jpg

Answered: 12.2 A T1 line is used to carry traffic…

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 15R

See similar textbooks

Similar questions

Need a sol
12.a. Which test can be used to measure splice loss?A. Tensile measurementB. OTDRC. Bit error rate testD. Continuity test 12.b. Which type of test should be performed on an installed cable after it has been terminated?A. Bit error rate testB. Continuity testC. OTDRD. Tensile measurement
3. In fixed channel assignment strategy, each cell is allocated a predetermined set of, a) Voice channels b) Control channels c) Frequency d) base stations
Need a solu
Solve it fast plz
Suppose that the circuit shown in the below figure is to be modeled. What is the correct VHDL option for the synthesis of this circuit? global_resetb zb- global cik a
What is ampere circuital law?
construct a "2 to 4 line decoder" using three “1 to 2 line decoders.”
The Vrms value is wrong
What is matched termination?
Why must kmaps consist of the following two things:1: groups have to be recanges with sizes of power 2 2: Why do we order our rows and colums 00/01/11/10?
asnwers: 1) relay at C (CT ratio) = 40 : 1 relay at B (CT ratio) = 60 : 1 relay at A (CT ratio) = 40 : 1 2) TMS/A = 0.711 3) top = 1.48 sec ( relay will operate as per the fault current level.) i) Design appropriate CT ratios for CTA, CTB, and CTC. (ii) Estimate time of Operation for all three relays for maximum value of fault current to maintain the selectivity. (iii) Determine TSM for relays at bus A and B for maximum fault current. (Use the standard formula for IDMT relays for these calculations.) (iv) Also use the standard curves for IDMT relays shown in Figure 2 to select TSM for relays at bus A and B for maximum fault current. Compare results obtained in (ii) and (iv). Verify the design to ensure that selectivity is maintained at minimum fault current for the fault in the same zone

SEE MORE QUESTIONS

Recommended textbooks for you

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

12.2 A T1 line is used to carry traffic from a remote concentrator to a central office. How many 10 CCS subscribers can the concentrator system support at 0.5% blocking. Compare an infinite source analysis to a finite source analysis. As- sume blocked calls cleared.