With the aid of a circuit diagram, show that two wattmeters can be connected to read the total power in a three-phase, three-wire system. Two wattmeters connected to read the total power in a three-phase system supplying a balanced load read 10.5 kW and −2.5 kW respectively. Calculate the total active power. Drawing suitable phasor diagrams, explain the significance of: (a) equal wattmeter readings; (b) a zero reading on one wattmeter. ANS: 8 kW

With the aid of a circuit diagram, show that two wattmeters can be connected to read the total power in a three-phase, three-wire system. Two wattmeters connected to read the total power in a three-phase system supplying a balanced load read 10.5 kW and −2.5 kW respectively. Calculate the total active power. Drawing suitable phasor diagrams, explain the significance of: (a) equal wattmeter readings; (b) a zero reading on one wattmeter. ANS: 8 kW

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Pls. write solution neatly
P2. A 100 volts rms single-phase voltage source feeds an inductive load of (30+j40) 2. Determine the value of capacitance to bring the power factor of the source to unity.
Fundamentals Of Energy Systems THQ1 Q1
(b) Differentiate between single phase and three phase alternating current (A.C) supply for the following aspects with adequate comparisons and sketches: (i) Generation of single phase and three phase e.m.f.s (ii) Sine waveforms(iii) Advantages or disadvantages of both phases
1.3 A 240 volts 50 Hz single phase ac source supplies a series load consisting of a resistor (40 ohms), a reactor (127.324 mH) and a capacitor (318.3 µF). Suppose that the frequency of the source can be varied at will. 1.3.1 Determine the maximum load current. 1.3.2 Determine the source frequency for maximum load current. 1.3.3 What is the name of this frequency? 1.3.4 Determine the load power factor. 1.3.5 What is the name of the source
v. With reference to an 50 Hz3 phase alternator explain how P,Q,V and F are controlled.
Please solve will give like!!!
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
Instantaneous voltage is multiplication of the resistace and .......... current in the resistive circuit. a) instantaneous b) average c) rms d) peak
A 1200 kVA, 6600 V 3 phase Y connected alternator has an effectiveresistance of 0.40 ohm and a reactance of 6 ohms per phase. It deliversfull load current at 0.80 power factor lagging. What will be the terminalvoltage for the same excitation and load current, if the power factor is0.80 pf leading? Whole Solution.
Indicate the equation that allows determining the voltage generated per phase, in a three-phase alternator supplying any type of load.
A three-phase, wye-connected induction motor is supplied by a three-phase and four-wire system with line-to-line voltage of 220 V and the impedance of the motor is 6.3 + j3.052 per phase. Determine the following: (a) The magnitude of the line current (b) The power factor of the motor (c) The three-phase average power consumed by the motor (d) The current in the neutral wire. 2.1