Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires ( 6%) of rated voltage to circulate (90%) of full load current at power factor (0.25) when the low voltage winding is short circuited and the no load loss is equal to (2500 W). Transformer B: 6600/420 V, (600 KVA) requires (9%) of rated voltage to circulate (80%) of full load current at power factor (0.16) when low voltage winding is short circuited and no load loss is equal to (4500 W). Calculate the followings: If both transformers are connected in parallel to supply a load (1.2 + j 2.3) ohm, find the output power of each transformer.

Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires ( 6%) of rated voltage to circulate (90%) of full load current at power factor (0.25) when the low voltage winding is short circuited and the no load loss is equal to (2500 W). Transformer B: 6600/420 V, (600 KVA) requires (9%) of rated voltage to circulate (80%) of full load current at power factor (0.16) when low voltage winding is short circuited and no load loss is equal to (4500 W). Calculate the followings: If both transformers are connected in parallel to supply a load (1.2 + j 2.3) ohm, find the output power of each transformer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 150 kVA, 2500/250 V, 50 Hz, single phase transformer has a no-load current of 0.75 A and a core loss of 850 W, when the high voltage side is energized at rated voltage and a frequency. Determine the following : 1) The core loss component of no-load current 2) The magnetizing component of the no-load current 3)The core loss resistance on the high voltage side in ohm 4)The magnetizing resistance on the high voltage side in ohm
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes.
BListen Tron Joss in a transformer: Cais dependent on load current. b) is a function of the resistance of the primary and the secondary windings. Cis a function of eddy currents and hysteresis effects in the transformer core. d) ) can be reduced by ¼ by reducing the current by 2.
Maximum efficiency of a single phase transformer occurs at 80 percent of full load. What is the ratio of core loss and copper loss at full load.
bị (a) Discuss THREE (3) important roles of the instrument current transformer (CT) and voltage transformer (VT) in power system operation.
Find the following : 1.Ripple Voltage (vpp) 2. Zero-to peak ripple(Vop) 3.secondary winding of the transformer high line and low line
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
1. A 40 kVA, 3300/240, 50 Hz single phase transformer has 660 turns on the primary, Determine: i. The number of turns on the secondary. ii. The maximum value of the flux in the core. iii. The approximate value of primary and secondary full load currents.
Q7/ Complete the blank The copper loss of a transformer at 4/5 of the full load is 4000 W, full load copper loss will be..........................................?
Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
A transformer core is laminated in order to ....................................? (A) reduce hysteresis loss and eddy current loss (B) reduce only hysteresis loss (C) reduce copper loss (D) reduce all of the above losses (E) None of the above.
Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer