Iron loss in a transformer: a) is dependent on load current. Ob) is a function of the resistance of the primary and the secondary windings. c) is a function of eddy currents and hysteresis effects in the transformer core. d) can be reduced by 4 by reducing the current by 2.

Iron loss in a transformer: a) is dependent on load current. Ob) is a function of the resistance of the primary and the secondary windings. c) is a function of eddy currents and hysteresis effects in the transformer core. d) can be reduced by 4 by reducing the current by 2.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Related questions

Q: A Single-phase transformer has a turns ratio 1: 2, and is connected to a purely resistive load as…

A: Given, A single-phase transformer has, Turns ratio, a=1:2. The magnetizing current, Im=1 A. The…

Q: 9. A single-phase transformer has a turn ratio of 6, the resistances of the primary and secondary…

Q: I need help with solving the question.

A: 7. Transformers are classified based on their construction into two main categories: Core type…

Q: 3. A 3200/400 single-phase transformer has winding resistance and reactance of 30 and 132…

A: In this question, We need to determine the equivalent terms in primary side and secondary side.

Q: For an ideal 2-winding transformer, the armpere-turns of the primary winding, N1/1, is equal to the…

A: For the magnetic circuit, the magneto-motive force is given as:

Q: ing is proportional to the current in that winding because (a) Ohm's law applies to magnetic…

A: In a transformer the leakage flux of each winding is proportional to the current in that winding…

Q: A transformer is operating at rated Voltage and Current and supplying a resistive load. With the…

A: The copper loss depends on the load resistance. When the load is increased, the copper load…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

BListen
Tron Joss in a transformer:
Cais dependent on load current.
b) is a function of the resistance of the primary and the secondary windings.
Cis a function of eddy currents and hysteresis effects in the transformer core.
d)
) can be reduced by ¼ by reducing the current by 2.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
An ideal transformer has no real or reactive power loss. (a) True (b) False
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
If we increase the load than core loss and copper loss will... Decrease Increase Remain same
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
P2-Draw the equivalent circuit of a single-phase transformer and explain how the core losses are almost invariant to the load (current). How do they depend on the terminal voltages of the transformer? Also, using the equivalent circuit explain how the copper losses depend on the load current.
What conclusions we come up with after doing open circuit test on single phase transformer.
Define all the losses in the transformer with the diagram and then define the hysterisis loss with thw graph.
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
3. The low-voltage winding of a 3000/200-V, 50-Hz, a single-phase transformer has 80 turns and is installed on a core with an efficient cross-sectional area of 150 cmz. Make a calculation on: a. the high-voltage winding's number of turns b. the value of the maximum flux density in the core
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.