transformers TransformerI want a short answer please1. The number of devices required to perform the no-load test and the short-circuit test for transformers.2. Explain the steps of conducting a no-load experiment for transformers.3. Explain the steps for conducting a short circuit test for a transformer.4. Draw a circle diagram..No load test5. Draw a circle diagram. Short circuit test6. What is the benefit of conducting a no-load test and a short-circuit test for transformers?7. What does the reading of the gauges used in the no-load test and the short-circuit test of transformers represent?8. If the frequency of the supplied source changes from 50 to 45 How will the electromotive force of the secondary be affected?9. Are there other ways - besides the load and no-load test - to test transformers and extract their constantsmore accurately? What is it? Sumpners test10.. Number of types of transformers in the laboratory and compare them in terms of working principle and work function.

Electrical machines can be either generator, transformer or motors. They can be either Ac machines…

Answered: 1. The number of devices required to…

Engineering

Electrical Engineering

1. The number of devices required to perform the no-load test and the short-circuit test for transformers.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer
Consider the following ideal transformer circuit in figure 1.
Explain the role of substations and transformers in power distribution and voltage regulation.
(a) A 5 MVA 230/11.5-kV single-phase power transformer has a per-unit resistance of 1.5% and a per-unit reactance of 6% (data taken from the transformer's nameplate). The transformer approximate equivalent circuit is given in the figure below. The open-circuit test performed on the low-voltage side of the transformer yielded the following data: Voc = 120 kV loc = 12 A Poc = 40 kW Refer to the low-voltage side of the transformer and calculate: (i) The value of Req and Xeq. (ii) The value of Rc and Xm. (ii) The voltage regulation when secondary voltage Vs = 11 kV and the secondary current Is = 350 A. kIp Reg jXcq 1, Vp Re V.
12.a. Comparing the transformer cores of core-form and shell-form transformers shows that thea. shell form provides lower reactance without increasing the transformer size.b. core form makes possible wider coils and better oil circulation.c. shell form is used exclusively in small low-voltage transformers.12.b. Distribution transformers are generally protected from damage due to excessive internal temperatures,by the operation of aA. lightning arrester.B. circuit breaker.C. surge diverter.
What is the purpose of transformers in the power transmission and distribution system?
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
What are the objectives of conducting an open circuit test on single phase transformer?
The label values of the single-phase transformer whose electrical equivalent circuit is given below are 20 kVA, 15400V / 240V, 50 Hz. This transformer Calculate what is required below. a. What is the value of the active power measured in the short circuit test? b. What is the value of the active power measured in the idle test? c. Voltage regulation was found to be 0.1% at 0.8 back power factor. Accordingly, using any method you want Find out how many kVA the transformer draws from the network (primary apparent power).
1.a. Separate voltage-regulating units provide voltage-ratio control under load byA. causing different impedance drops in each phase.B. combining voltages from different phases.C. having series transformers in phase with the line-to-neutral voltage.D. exciting transformers having their primaries delta-connected. 1.b. A reactor is sometimes used with an autotransformer toA. limit short-circuit current.B. increase the full-load current.C. provide increased internal impedance.D. decrease the voltage ratio.
Investigate the different types of power transformers that exist today, mentioning their principle of operation (power transformer without mentioning their variants) Investigate the types of Instrument transformers (current and potential) and mention the principles of operation.
Discussion : 1- What are the advantages and disadvantages of this test ? 2- Why it's imporctical carry out actual load test on large rating transformers ? 3- What will be the current in the primary windings? i) When secondaries are not loaded ? ii) When secondaries are loaded ?