Q3-(A)- Three single-phase, 50 kVA, 2310/ 230 V, 60 a 3-phase, star /delta, 4000/230V transformer bank. The equivalent resistance of transformer referred to low-voltage is 0.012 and the equivalent reactance of each transformer referred to low-voltage is 0.016 W. The 3-phase transformer supplies a 3-phase, 120 kW, 230 V, 0.85 power-factor (lagging) load. (i) Draw a schematic diagram showing the transformer connection. (ii) Determine the winding currents of the transformer.

Q3-(A)- Three single-phase, 50 kVA, 2310/ 230 V, 60 a 3-phase, star /delta, 4000/230V transformer bank. The equivalent resistance of transformer referred to low-voltage is 0.012 and the equivalent reactance of each transformer referred to low-voltage is 0.016 W. The 3-phase transformer supplies a 3-phase, 120 kW, 230 V, 0.85 power-factor (lagging) load. (i) Draw a schematic diagram showing the transformer connection. (ii) Determine the winding currents of the transformer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

please solve the question lmlmlmlm
Two transformers A and B of different ratings but equal voltage ratios share a load of 900 kVA at 0.8 power factor lagging at 400 V by operating in parallel. Transformer A has a rating of 600 kVA, resistive drop of 1% and reactance drop 5%. Transformer B has a rating of 300 kVA, resistive drop of 1.5% and reactance drop of 4%. Calculate the load shared by each transformer and the power factor at which it is working.
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. Assuming an ideal transmission line, compute the load voltage (line-to-neutral).
A transformer has 600 primary turns and 300secondary turns. The primary and secondary resistances are 0.35 and 0.09 respectively and the corresponding leakage reactances are 1 and 0.08 respectively. Determine (a) the equivalent resistance referred to the Secondary winding, (b) the equivalent reactance referred to the Secondary winding, (c) the equivalent impedance referred to the secondary winding, and (d) the phase angle of the impedance.
A normal transformer has a nominal 60 kVA. The nominal primary and secondary voltages are 600 V and 120 V respectively. If this transformer is connected as an autotransformer at 600 Vac a-) What would be the output voltages available using different connections? b-) Calculate the load kVA that the transformer can supply for each of the output voltages. c-) Calculate the currents of the windings for each one of the output voltages, indicating if it exceeds the nominal values.
Please give an explanation for each step
Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires ( 6%) of rated voltage to circulate (90%) of full load current at power factor (0.25) when the low voltage winding is short circuited and the no load loss is equal to (2500 W). Transformer B: 6600/420 V, (600 KVA) requires (9%) of rated voltage to circulate (80%) of full load current at power factor (0.16) when low voltage winding is short circuited and no load loss is equal to (4500 W). Calculate the followings: If both transformers are connected in parallel to supply a load (1.2 + j 2.3) ohm, find the output power of each transformer.
A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
A 2000/400 V, 100 kVA, 60 Hz step-down single-phase transformer has a primary and secondary resistances of 0.2ohm and 0.05 ohm respectively, the corresponding leakage reactances being 0.3 ohm and 0.01 ohm respectively.1. Calculate the equivalent resistance, reactance and impedance referred to the low-voltage (secondary) side.2. Find the high (primary) voltage when the transformer is supplying full-load current at rated secondary voltage at 0.8 powerfactor lagging.3. Draw the phasor diagram showing your answer in 2.
Maximum efficiency of a single phase transformer occurs at 80 percent of full load. What is the ratio of core loss and copper loss at full load.
Which of the following statements is true about an ideal transformer? O It changes the magnitude of DC signals. O It converts DC signals into AC signals. O It changes the magnitude of AC signals. O It converts AC signals into DC signals.
Determine the regulation of a transformer in which thepercentage resistance drop is 1% and the percentagereactance drop is 5% when the power factor 0.8 leading.