The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN.   2.1 Determine the tensile stress in each rod.                                                                2.2 Determine the shear stress in pin A between the members.                                    2.3       If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint

Q: The pole is supported by a pin at C and an A-36 steel guy wire AB. B. 3 ft 30 2.5 kip 4 ft Part A If…

A:

Q: Question 2) Forces of F1=3 kN in the z direction from point B, F2=9 kN in the z direction from point…

A:

Q: An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 m…

A: Given-Data:- Wide b =100mmx=2.4md1=450mm=0.45md2=300mm=0.3mμ=0.3T'=14N/mmN1=120rpm To-Find:-…

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

A: Given data: F=600 Ndi=25 mmt=5 mm Need to determine the maximum shear stress in the tube.

Q: Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint.…

A:

Q: Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of…

A: As it is not mentioned that which three parts need to be solved, please find solutions of first…

Q: The lap joint shown is fastened by five % inch-diameter rivets. The bearing stress in the plates is…

A:

Q: A square pedestal has glued parts at joints t, r, e, and s. Plane t-r-e-s is at anole of 30° from…

A: Given: The allowable compressive stress = 5.2 Mpa The inclination of plane = 30 degree The shear…

Q: The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70…

A:

Q: solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: Given data as per questionLoad on the bar =25 kg=245.25 NLimiting stress of the bar =27.24kpawe know…

Q: In the assembly shown, rod AB is made of steel (E = 200 GPa) and has a diameter D = 50 mm. Rod BC is…

A: Given data: STEEL…

Q: Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the…

A:

Q: Q2b) The supporting wheel on a scaffold is held in place on a leg using a 6 mm diameter pin as…

A:

Q: Q1. For the figure shown below, the rigid platform has negligible mass and rests on two steel bars,…

A:

Q: 6.* Figure 6 shows two plates of thickness t = 6 mm and width (into the paper) 50 mm tha are joined…

A: please refer handwritten solution

Q: = Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take di = 30…

A:

Q: The vertical force P acts on the bottom of the rod having a negligible weight and a rectangular…

A:

Q: Problem 1-3 The Cartesian components of stresses at a point are given as belou : O = 7, 0y = 6, oz =…

A: The cartesian components of stresses at a position specified in the inquiry are known to us :…

Q: Question 2)  arm of Figure  B  from point x z  plane, a horizontal angle of θ = 38 ° angled F = 29…

A:

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

A:

Q: Q2. As shown in figure, the allowable stress for tension is 200 MPa and the allowable stress for…

A:

Q: The lap joint is fastened with four 3/4-inch diameter rivets. a. If the allowable shearing stress of…

A:

Q: Consider the frame in (Figure 1). The crate weighs 400 lb. Follow the sign convention. Figure 4 ft A…

A:

Q: Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by…

A:

Q: The figure below shows two plates connected by two rivets. The plates are made from aluminum 6061-T6…

A:

Q: Question 1: A steel rod is rigidly attached between an aluminum rod and a bronze rod as shown .…

A: Given   Area of steel, A = 400 mm2     Stress at steel = 140 MPa Find   Maximum load, P

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

A:

Q: Two 2 by 4 cm 1062 steel bars are butt-spliced with two 3 by 4 cm 1016 splice plates using six M14…

A: We have to find the correct formula for finding shear stress

Q: 4. A standard brick (dimensions 200mm x 100mm x 65mm) is compressed lengthwise by a force P as…

A:

Q: 6. The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the…

A: GIVEN DATA- G=70*10^3 psi Thickness t=1/2in we have to find value of force P

Q: -28 The steel pipe column shown in Fig. P2-28a has an out- side diameter of 150 mm and a wall…

A:

Q: The "C" clamp shown in the following figure has a rectangular cross section at location "a-a" with a…

A:

Q: 10 rivets are fastened on a lap joint of 1.25 inch in diameter the thickness of the lap join were…

A: Given: Number of rivets→n=10 Diameter of the each rivet→d=1.25 inch Hence area for shear…

Q: A column is made of the two materials side by side as shown. Each material carries a portion of the…

A:

Q: Determine the normal force at point E Express your answer to three significant figures and include…

A:

Q: in 5 minutes please Diameter=38 L

A:

Q: Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh .If the…

A:

Q: The structure supports a distributed load of w. The limiting stress in rod (1) is 400 MPa, and the…

A: Free body diagram of the structure is given below,

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.