A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the section M and the screwed section N, where the diameter at the root of the thread is 4 mm as shown in Figure Q1.2. M 40 kN 1. 40 kN- 4 mm diameter 6 mm diameter

A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the section M and the screwed section N, where the diameter at the root of the thread is 4 mm as shown in Figure Q1.2. M 40 kN 1. 40 kN- 4 mm diameter 6 mm diameter

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. The stepped circular bar shown below is made from aluminum (E = 70 GPa, v = 0.35). Each segment is 400 mm in length. Prior to applying the loads, the bar has the dimensions shown. The structure is axially loaded as shown. Determine the stress in each segment, the maximum stress and its location, the final in length of the structure, and the final diameters of each segment due to the applied loads. All dimensions shown are in mm. Ø 25 40 15 ↑ Fu 300 kN 600 kN 300 kN
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
Figure 2.1. shows two long plates with same material and equal width w=20 mm that are subjected to a uniaxial tensile load o. One of the plates has a single small central hole with diameter 4mm and another plate has two small holes with a distance of 8mm from each other. The holes are perpendicular to the external tensile load. Develop a computer code (or simulation model) and analyze how stresses will be distributed at the tip of the holes in these two plates for different values of 0. 4mm Figure 2.1. 8mm 4mm
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the section M and the screwed section N, where the diameter at the root of the thread is 2. 4 mm as shown in Figure QI.2. (6) M - 40 kN 40 kN - 4 mm diameter 6 mm diameter Figure Q1.2: Steel bolt
2 3.0 m 175 KN 2.5 m 200 KN (1) (2) 46 mm 175 kN 30 mm Problem 3 A compound axial member consists of steel (E=200 GPa) segment (1) and brass (E=120 GPa) segment (2). a) Compute the total deformation of the compound member for the loading shown (in mm). b) Sketch an internal normal force diagram c) Calculate the average axial stress in segment 2
1. Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square cross section and bar width is 15 mm. Points A, B and C are pin connections. Square 15 mm side 6m 3.5m C 20KN
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
mm. NegiCOL UIC wOg VA vUampvuva 1.4-12 A rigid member DAC as shown in Fig. P1.4-12 carries the load P. Bar AB is an aluminum bar whose cross-sectional area is 0.5 in, and it is pinned at A and B by 0.5-in-diameter pins in a single-shear configuration. If the maximum allowable normal stress in AB is 7000 psi and the maximum allowable shear stress in the pins is 15,000 psi, find the maximum allowable load P. For aluminum E 10 x 10° psi. %3D 8 ft 7 ft P B Fig P1.4-12
1.2 Figure 1 show a compound bar made of the aluminum alloy with three different cross-sectional. The bar is subject to a tensile load of 40KN. Take E = 69 GPa, Determine the stress in each section and the total elongation of the bar 30 mm 40 mm 50 mm 40 kN 40 kN 0= 20 mm 0= 15 mm 0 = 10 mm