Ql:A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceced an overall deformation of 0.5 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 100 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use E = 200 GPa, E = 70 GPa, and E = 83 GPa. st al br Bronae A-650 m Steel Aluminum A= 480 mm A 320 mm 4P 2P 1.0 m 20m 1.5m

Ql:A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceced an overall deformation of 0.5 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 100 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use E = 200 GPa, E = 70 GPa, and E = 83 GPa. st al br Bronae A-650 m Steel Aluminum A= 480 mm A 320 mm 4P 2P 1.0 m 20m 1.5m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at other end in a length of 600 mm. If the bar is subjected to a load of 80 kN, find its extension. Take E = 2 x 10 MPa. What is the percentage error if average area is used for calculating extension?
SHOW ILLUSTRATION AND SOLUTION Problem 1: A steel rod with a cross - sectional area of 150 mm2 is stretched between 2 fixed supports. The tensile load at 20 oC is 5 kN. Use E = 200 GPa and  = 11.7 x 10- 6 /oC 1. At what temperature will the stress be zero?2. What will be the stress at - 20
Q2/ For assembly shown in the figure. Determine the stress in each of the two vertical rods if the temperature rises 40 °C after the load P=50 kN is applied. Neglect the deformation and mass of the horizontal bar AB. Use E aluminum=70 GPa, coefficient of thermal expansion of aluminum=23.0µm/m°C, A aluminum=900 mm2, E steel=200 GPa, coefficient of thermal expansion of * .steel=11.7 um/m°C and Asteel=600 mm2 Steel Aluminum 4m 3m A B 3 m 3 m 3 m 50 kN
The figure shows a flat hanger bar for supporting shop equipment in a factory. The bar is fixed to a support by means of a bolted connection. The main part of the hanging bar is 1.5 inches wide. This width varies up to 3.0 inches. A 1.0-inch diameter bolt transfers the hanger bar load to the two top bracket plates. Determine the allowable stress of the tension load P in the hanger in the following two instances: to. The allowable tensile stress in the main part of the hanger is 16,000 psi. b. The allowable stress load between the hanger bar and the bolt is 26,000 lb/pu.
Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are both made of SAE 1340 OQT 1000 steel (Sy= 950 MPa, E = 200 GPa). Take D; = 75 mm and D, %3D %3D 90 mm. Determine the maximum possible value of the tangential stress at the inner surface of the outer element in MPa. NOTE: Answer is not 4750MPA. If you Submit This answer I will Directly report. |D, H6/s5 D. 6/7
4) A composite section 2 m in length, consisting of a steel tube with outer diameter 24 m and thickness 3 mm, enclaves a solid copper har 18 mm diameter. An axial compressive load of 250 KN is applied on the assembly, Young's modulus for steel and copper are taken a 2 x 10 N/mn und I x 10 Ntm respectively. Calculate the stresses developed in stoel and ccipper. Also caleulate the load taken by both the materials.
2. The bottom shell of a steel tanker is longitudinally framed. The spacings of transverse floor and longitudinal are 5 m and 0.8 m respectively. The bottom plating is 12 mm thick and the longitudinals are 150 x 10 mm flat bar. For higher- tensile steel, Young's modulus E = 210 kN/mm and yield stress oy = 340 N/mm?. Calculate the Euler buckling stress of the stiffened bottom panel and comment on the result. State any assumptions made. [342 N/mm]
The steel propeller shaft ABCD carries the axial loads shown in the figure. Determine the change in the length of the shaft caused by these loads. Use E = 29x10° psi for steel. 0.75 in. 6000 lb 0.75 in. 0.5 in. 2000 lb 4000 lb B| C D 5 ft- 4 ft 4 ft – a. Identify the type of deformation in each segment in the problem. b. Set up the equations of deformation that is required to solve the problem. c. Solve for the unknown variables using the equations derived previously.
Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC that is welded to tube AB via plate B. The cross-section area of the tube is equal to 1100 mm2 and the diameter of the rod is equal to 15 mm. calculate the axial deformation of point C? (Esteel=200GPa and EAl=70GPa)
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
1. A steel rod of 25 mm diameter is enclosed centrally in a copper hollow tube of external diameter 40 mm and internal diameter 30 mm. The composite bar is then subjected to an axial load of 4500 N.If the length of each bar is equal to 130 mm, calculate: 1. The stress in the rod and the tube 2. Load carried by each bar. Take Es=2.1x105 N/mm2 and Ec=1.1x105 N/mm2
For 13 to 15. The compound bar carries the axial forces P and 2P. The working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2 in. 3 ft 4 ft 2P Steel Aluminum A = 0.6 in.² A=0.4 in.2 E = 29 × 106 psi E = 10 x 106 psi 13. What is the maximum allowable value for P? 14. Give the elongation of the steel section provided that the maximum allowable P is applied. 15. Give the elongation of the aluminum section provided that the maximum allowable P is applied.