(A) Q: A 400 mm external diameter steel cylinder with a nominal internal diameter of 240 mm is shrunk onto another steel cylinder of 240 mm external diameter and 140 mm internal diameter. The radial interference 8 is 0.3 mm. Use Young's Modulus E = 200 GPa and Poisson's Ratio n = 0.3. Find: 1. tangential stress at the outer surface of the inner cylinder; 2. tangential stress at the inner surface of the outer cylinder; and 3. radial stress at the junction.

(A) Q: A 400 mm external diameter steel cylinder with a nominal internal diameter of 240 mm is shrunk onto another steel cylinder of 240 mm external diameter and 140 mm internal diameter. The radial interference 8 is 0.3 mm. Use Young's Modulus E = 200 GPa and Poisson's Ratio n = 0.3. Find: 1. tangential stress at the outer surface of the inner cylinder; 2. tangential stress at the inner surface of the outer cylinder; and 3. radial stress at the junction.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
A solid brass bar of diameter d =1.25 in. issubjected to torques T1, as shown in part a of the figure.The allowable shear stress in the brass is 12 ksi.(a) What is the maximum permissible value of thetorques T1?(b) If a hole of diameter 0.625 in. is drilled longitudinallythrough the bar, as shown in part bof the figure, what is the maximum permissiblevalue of the torques T2?(c) What is the percent decrease in torque and thepercent decrease in weight due to the hole?
What is the difference between static and dynamic loading.. Explain with the drawing the types of dynamic loading. b) In the figure shown, a column of AIAL 1045, cold drawn, rotates on bearings. A force of SKN is applied to it8kn . Find the modified resilience limit stress, the stress of Al-Tin Amra
The stepped shaft in the figure transmits 19.2 kw of power at 180 rpm. Maximum strain Determine the required shaft diameter using the Von Mises hypothesis. (L=0.8 m, F=6kN, tem=72 MPa, gem= 108 MPa F Mb A 3L/5 2L/5
I need the answer as soon as possible
3. A rectangular solid bar of width 20mm and depth 35mm is subject to a pure positive moment of 450Nm. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line. 4. The bar in Q3 is also subject to a tensile load of 15kN applied at the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line.
5 - A thin-walled pressure vessel is subjected to internal pressure p 1 MPa. What is the maximum allowable torque T, applied along the longitudinal axis, if the maximum allowable tensile stress is 80 MPa? ↓t=3mm 240mm polar moment of inertia J=2r³t
A hellcal spring Ils made by wrapplng steel wire 20 mm diameter around a forming cyllnder 160 mm in diameter. Calculate the elongatilon of the spring wlthout exceeding a shearing stress of 150 MPa If It ls composed of 20 turns. Let G=80,000 MPa. (Ans. 127.4 mm)
2. Justify the simplification of this problem to only modeling one-eighth of the cross section 3. Construct two-dimensional elements grid (i.e., grid/mesh region), make the correct numbering and labeling of the nodes and elements.
A hard-drawn steel wire extension spring has a spring index Of 7.5, hook radii of r = 0.106 in and r2 0.089 in, and an initial tension of 1.5 lbf. The number of body turns is 13.5 and the uncorrected initial stress is 16.5 kpsi. From the given information: (a) Determine the physical parameters of the spring. (b) Find all stresses at ends A and B and the body torsion under the static load of 6 Ibf.
a 4ll Asiacell Q2 A 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm external diameter and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+SN) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm. Find the number of turns for the nut and stress in bronze tube.2. If the temperature of the steel and bronze is then raised to 40°C find the changes that will occur in the stresses in both materials. The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2. E for bronze = 100 GN/m2. Where SN=3 إجابتك