A torsional moment T = 8,867 Nm and a load P = 59,372 N are applied at the same time to a circular hollow shaft of unknown length L, as shown in Figure Q9. The shaft has an inner diameter d = 49 mm and an outer diameter D = 70 mm. Point A in Figure Q9 is on the outer surface of the shaft.        Figure 9   Calculate the maximum in-plane shear stress at point A. Use π = 3.14159 if needed. Calculate your answer in the unit: mega-Pascal (MPa). Report you answer to 3 decimal places.

Q: n the figure shown, the cutaway view shows a solid aluminum alloy of L= 600mm, A= 707mm^2 and E=…

A:

Q: A circular tube of inner radius r1 and outer radius r2 is subjected to a torque produced by forces P…

A: a-calculate the r2 the minimum permissible outer radius of the tube given…

Q: A torsional moment T = 6,467 Nm and a load P = 87,599 N are applied at the same time to a circular…

A: This question is related to the torsion of the shaft. torsional shear stress or Torsional stress is…

Q: QUESTION 8 A torque T is applied on an aluminium shaft acting at the ends (see figure). The shaft is…

A:

Q: A solid tapered steel shaft is rigidly fastened to a fixed support at one end and is subjected to a…

A:

Q: torque that will cause a maximum shear stress of 10 000 psi. Use G = 4x 106 psi for aluminum. e-4…

A: Solnn:- in a given figure  Sear stress=10000 psi G= 4×10^6 psi Now, enclosed area Am= π\2  ×  r^2 +…

Q: The figure shows a stepped steel shaft supported in bearings at A, C and loaded by a 2 kN force at…

A: please refer handwritten solution

Q: Pravinbhai

A: The objective of the question is to calculate the factor of safety for fatigue using the Goodman…

Q: simply supported beam of inverted T-section shown in Figure 5, of the working stresses are 48 MPa in…

A: The maximum tensile stress is .The maximum compressive stress is .The maximum shear stress is

Q: A 1.25-in-dia solid steel shaft with several twisting couples is shown in figure 1. For  TA = 10000…

A: Given data: TA= 10000 lb.inTB= 20000 lb.inTC= 30000 lb.ind=1.25 in Need to determine the magnitude…

Q: A bar of steel has the minimum properties Se= 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is…

A: Given:The endurance stress is The yield stress is The ultimate stress is The steady torsion stress…

Q: A flat bar with a hole (see figure) has widths b = 60 mm and c = 40 mm. The fillets have radii equal…

A: b = 60 mm c = 40 mm R = 5 mm to determine diameter dmax of the largest hole

Q: A prismatic bar of length L with a solid circular cross section of diameter d is loaded by a…

A:

Q: A solid steel bar of circular cross section has diameter d = 40 mm, length L = 1.3 m and shear…

A: A solid steel bar of circular cross section has diameter d = 40 mm = 0.04 m, length L = 1.3 m and…

Q: This is a multi-part question. Once an answer is submitted, L- P

A: Given-Information:- Length, L = 4 m Angle size 100×100×12 mmP =3000 N a =1.75 m =1750 mmW =1000 N/m…

Q: A torsional moment T = 7,005 Nm and a load P = 92,107 N are applied at the same time to a circular…

A: Given data:- Torque = 7005 N-m Force = 92107 N Eccentricity = 6 mm inner diameter = 46mm Outer…

Q: T.L J =- (r* – r*) (Tubular shaft) Tr J = (Solid shaft) G.J 3. The shaft in the figure below…

A: Free body diagram: From the FBD: TA+TB=5100 N-m    .....(1)For parallel connection, Angle of…

Q: 6. A circular bar AB with ends fixed against rotation has a hole 25 in. 4 130 in ending for half of…

A:

Q: The figure below shows a section of a column subjected to load P, which is applied 50 mm from the…

A: Given: Distance of the load from the from the middle of the section's web: →r=50 mm=0.05 m Area of…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.