EXAMPLE: 4. A 2-in.-diameter steel tube with a wall thickness of 0.05 inch just fits in a rigid hole. Find the tangential stress if an axial compressive load of 3140 lb is applied. Assume v = 0.30 and neglect the possibility of buckling. (Practice at Home) 0.05" 2.0" 0.05" Rigid Wal 3140 lb Rigid Wall

EXAMPLE: 4. A 2-in.-diameter steel tube with a wall thickness of 0.05 inch just fits in a rigid hole. Find the tangential stress if an axial compressive load of 3140 lb is applied. Assume v = 0.30 and neglect the possibility of buckling. (Practice at Home) 0.05" 2.0" 0.05" Rigid Wal 3140 lb Rigid Wall

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The bottom shell of a steel tanker is longitudinally framed. The spacings of transverse floor and longitudinal are 5 m and 0.8 m respectively. The bottom plating is 12 mm thick and the longitudinals are 150 x 10 mm flat bar. For higher- tensile steel, Young's modulus E = 210 kN/mm and yield stress oy = 340 N/mm?. Calculate the Euler buckling stress of the stiffened bottom panel and comment on the result. State any assumptions made. [342 N/mm]
A steel column of hollow circular cross section shown in Figure is supported on a circular steel base plate and concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN.a. Determine the bearing stress induced by the column to the base plate in MPa.b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
In the figure, member AB is used to support a load of 20kN at the free end, if the cable CD has adiameter of 25mm, what is the tensile stress in the cable?
3 Solve it, and draw a free body diagram.
Fined the stress in each segment and the displacement in each segment
4. Show your complete solution.
Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 70 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 8 mm, and an allowable normal stress of 170 MPa. Assume x1 = 2.9 m, x2 = 1.9 m, and y1 = 4.3 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) (2) Answer: Pmax i kN
The flat bar shown in the figure is subjected to tensile forces P = 3000 lb. The bar has thickness t = 0.25 in. a) If the designer wants to make a stepped bar with shoulder fillets as shown in the figure, determine R the maximum stresses for fillet radii R = 0.25 in. P and R = 0.5 in. if the bar widths are b = 4.0 in. and c = 2.5 in. b) Comment on the relation between the stress and the fillet radius each time it is increased. c) What is the factor of safety for each fillet radius if the part is made of cast iron Sut = 30 ksi? Solution: 3.0 2.8 D/d = 2 1.15 D. 2.6 1.5 2.4 2.2 - 1.05 O nom %3D %3D td к, 2.0 3.0 1.8 E 1.6 E 1.01 1.4 E 1.2 1.0 0.05 0.10 0.15 0.20 0.25 0.30 r/d
PROBLEM 2 The composite bar is rigidly attached to unyielding supports. The bar is stress-free at 65°F. At what temperature will the aluminium and steel segments in the given figure have stresses of equal magnitude after the 12.5 kip force is applied? The coefficient of linear expansion of aluminium is a = 12.8 x 10-/°F and steel is a = 6.5 x 10-/ºF Aluminum Steel A = 2 in.2 E = 10 × 106 psi A = 3 in.2 E = 29 × 106 psi 12.5 15 in.- -10 in.-
2. A 2-in.-diameter steel tube with a wall thickness of 0.05 inch just fits in a rigid hole. Find the tangential stress if an axial compressive load of 3140 lb is applied. Assume v=0.30 and neglect the possibility of buckling. data: 2 in Rod Wall Rod Vill
Brass Problem 3: A composite bar is made by attaching a copper rod of length 900 mm and diameter 30 mm and a brass rod of length 600 mm and diameter 45 mm as shown. A load of 20 kN is applied at 20°C. For unyielding supports, find the stresses in the materials when the temperature rises to 50°C. For copper, E = 120 GPa and a = 18 x 10-6 °C. For brass, E = 90 GPa and a = 20 x 106 °C. Copper 20 kN 900 mm 600 mm
A 3-in. by 6-in. steel (E-29,000 ksi) bar (4-foot long) is subjected to the loads shown. Calculate the combined stresses at points A and B (be sure to indicate either tension or compression). Remember, the bar is bending in the strong direction so calculate your I accordingly. 1(1/12) (B)"(H) S=l/c A B. 6" 10,000 lbs 45,000 Ibs