The box beam shown in Figure P8.63b has dimensions of b = 80 mm, d = 120 mm, and t = 8 mm. A downward concentrated load of P = 42 kN acts on wall BC of the box at a distance of a = 35 mm below the z centroidal axis as shown in Figure P8.63a. Determine the normal stress: (a) at corner A. (Ans. to check: 22.9 Mpa (T)) (b) at corner D. (Ans. to check: 9.01 Mpa (C))

Q: A 12 inches square steel bearing plate lies between an 8 inches diameter wooden post and a concrete…

A:

Q: 2. The setup for an experiment consists of a curved steel beam with a rectangular cross section…

A:

Q: lg (6) Im الله Soan

A:

Q: The box beam shown in Figure P8.63b has dimensions of b=80mm, d=120mm, and t=8mm. A downward…

A:

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A: Given that, Radius of gyration of column, k=150 mm,Cross-section area, A=0.02 m2Modulus of…

Q: The assembly in Figure consists of a light rigid bar AB, pinned at O, that is attached to the ste…

A: Given             Deflection = 5 mm          Area of steel = 250 mm2 Area of aluminum = 300 mm2 Find…

Q: 5. The equilateral triangular tórsión member has sides equai lU D thickness t (Figure a). Figure b…

A: TMAX=100mpaG=70×103 mpab=16cmt=1cmTJ=ζr=GθLwhere θ and L consider as 1

Q: For the rigid bar (AB) and rod (BC) system, the normal stress in rod BC can't exceed 30 ksi. The…

A:

Q: Calculate the bearing capacity for a 2 * 3 rectangular foundation that is kN under eccentric load as…

A:

Q: For the cantilever beam arrangement shown below, address the following: (a) Determine the forces…

A:

Q: See the figure below. AD is a member with varying diameters. There are three axial loads applied at…

A: Given data: The magnitude of the force acting at the point B is; F1=10 lbs. The magnitude of the…

Q: An angled strut b = 6.2 in. thick is subjected to a force F = 55 kip and a uniformly distributed…

A: The values are F=55 kipq=23.5 kip/ft The thickness is b=6.2 in     To find out:- The principal…

Q: 1. Determine the maximum shear stress acting at section a-a of the cantilevered strut; L₁ = 1 ft, L2…

A: The objective of the question:Determine the maximum shear stress acting at section a-a of the…

Q: A bearing supports a 28mm diameter solid steel torsion rod (plan view shown in Fig. 1) rigidly…

A: Given data Diameter =28mmarm=300mmvertical load=2500 N

Q: A solid circular composite bar (made of aluminum in segment AB, steel in segment BC and Brass in…

A:

Q: The bracket shown in the figure below is fixed supported and has an applied force of 5kip with 40…

A:

Q: The beam supports the triangular distributed load shown below with Wmax = 900 lb/f The reactions at…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.