A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding 14m

A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding 14m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

write your solution clearly.thanks
3.9 A thin cylindrical steel drum, 10 mm thick, is subjected to an internal pressure of 1,5 MPa and rotates at a speed of 250 r/min. Calculate the maximum permissible diameter of the drum if the allowable hoop stress is 120 MPa (specific gravity of steel = 7,85). What would the required diameter be if the cylinder was not rotated?
Solve it correctly please.
In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5 x10−3 cm2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute:(a) The tensile strain and(b) The elongation
Calculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10 MPa. The thickness of the vessel is 38 mm and the hoop stress is 83 MPa and the longitudinal stress is 40 MPa. 1 Add file
Q3. A welded steel cylindrical drum made of a 15mm thickness plate has an internal diameter of 1.50 m. Compute the change in diameter that would be caused by an internal pressure of 3.0 MPa. Assume that Poisson's ratio is 0.27 and E = 200 GPa Thickness t= 15mm y 1. 5m
Q3. A welded steel cylindrical drum made of a 15mm thickness plate has an internal diameter of 1.50 m. Compute the change in diameter that would be caused by an internal pressure of 3.0 MPa. Assume that Poisson's ratio is 0.27 and E = 200 GPa Thickness t= 15mm 1.5m
Please show the complete solution with a diagram and label. Avoid shortcut solutions.
Thank you!! Calculate the maximum tensile stress in a plate subjected to a remote loading of P. The plate has a central hole as shown below. The stress concentration at the hole is 2.5 based on the remote average stress. The Plate thickness is 1cm, plate width 20 cm and the total load P is 25 kN. Identify the location of the maximum stress at B
The cross section of a concrete dam is shown in the figure. Take the weight-density (= pg) of water to be 10 kN/m³ and that of concrete to be 25 kN/m³. For the given design of the cross-section, find the ratio h/H that is safe enough for the dam to not tip over (about the downstream edge E). Here you will enter the numerical answer. In the handworked file you must show your worked solution. H E 60° H/10 4H/10 h
A cylindrical steel pressure vessel 200 mm radius with a thickness of 20 mm, is subjected to an internal pressure of 5.0 MN/m². Calculate the tangential stress in the steel.
A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the stress in the rope?