solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the limiting stress of the bar is 27.24 kPa determine the cross sectional area of the steel square bar and its dimensions.

Q: A Truck in which the pair of wheels at the rear side carries a load of 1.5 Tonnes on each axle box,…

A: Given: Maximum allowable stress: →τ=100 N/mm2 Load on each axle box: →P=1.5 tonns…

Q: E 0.100 m PPP 0.150 m 0.300 m 0.250 m D

A:

Q: A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN. Determine…

A:

Q: A U-bolt supports a load of 5,000 lb. The cross-section of the bolt has a diameter of ½ in. How…

A: Given: Load supported by the U-bolt = P=5000 lb Diameter of bolt = d=0.5 in

Q: А cube with an edge of 2·5 cm as shown in Fig. 1.4 was tested in compression. Under a load of 400 kN…

A: In compression, we examined a cube with a 2.5 cm edge, as illustrated in the picture. It failed…

Q: A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: given data;load=mg=25*9.81=245.25Nlimiting stress σ=27.24kpa=27240Pa=27240N/m2cross sectional…

Q: For the clevis connection shown, the shear stress in the 0.21-in.-diameter bolt must be limited to…

A: Given: Let us consider the given data, Shear stress,  τ=39 ksi=39×103 Psi Bolt's diameter, d=0.21 in…

Q: The homogeneous bar ABCD shown in the figure below is supported by a cable that runs from A to B…

A: The stress in cable is The area of cable AB is The area of cable at C is Point D is smooth

Q: What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a…

A: Given data:- load =1000 Ncross-section area =20 mm 30 mmTo find:-the stress in a rectangular rod (…

Q: (12) A square steel bearing plate lies between a wooden post and a concrete footing as shown.…

A: Given     Stress in wood = 12.5 MPa Stress in concrete = 4.5 MPa Find   Maximum value of the load, P

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: P= 189.3 kN= 189.3(1000) N= 189300 N Cross sectional area of the bronze, ABronze= 400 mm^2 Magnitude…

Q: rmine the support reaction at D pade of solid cvlindors: ARİS S

A:

Q: Determine the tensile stress in a bar of 20 mm diameter when it is subjected to a pull of 450 N.

A: According to the information we have a force of 450 N and the diameter is 20 mm where tensile stress…

Q: A square key is to be used in a 40 mm diameter shaft and that will develop a 2 kN-m torque. If…

A: Calculate the force acting on the key. F=Td2 Here, F is the force acting on the key, d is the…

Q: An object weighing 40 N is drop from a height of 4 m and hits a vertical steel rod on top. Determine…

A: Weight of object = W = 40 NHeight of drop = h = 4 m = 4000 mmDiameter of rod = d = 4 mmLength of rod…

Q: The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.

A:

Q: A compressive load of 2.4 kN acts on a circular bar of 200 sq. mm area and 20 mm high. It…

A: Load P=2.4 kNArea A=200 mm2Length/height L=20 mmCompression To Find-The value of Young's modulus of…

Q: A straight girder of uniform section and length L rests on supports at the ends, and is propped up…

A:

Q: y, determine the required diameter of the rod.

A:

Q: Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin…

A: Two horizontal 7.5-kip forces are applied to pin B of the assembly shown.A 0.8-in diameter pin is…

Q: Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh .If the…

A:

Q: A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of  21 MPa.…

A: Dear student, there is some additional data given which is of no use. Please find the attached…

Q: A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged…

A:

Q: 1. A 16-cm square steel bearing plate lies between a 12-cm diameter wooden post and a concrete…

A:

Q: For the given machine part, where the cross-sectional area at m-n is a square with side 5 mm,…

A: The largest allowable value of the distance: e = 11.6667 mm.

Q: 2. The homogeneous 1000-lb plate is suspended from three cables. Determine the smallest diameter…

A:

Q: Given the assembly shown is a cylinder rod position vertically and is supported by a collar and a…

A: Shear failure between collar and cylinder: Area of shear occurs between collar and cylinder…

Q: A 2m long bar with square cross section of side 40 mm is subjected to compressive stress of 70 MPa…

A:

Q: Determine the maximum stress produced in a rectangular plate 50 mm wide, 8 mm thick with a central…

A: Given that, Axial tension, P=1 kN,Width of rectangular plate, b=50 mm,Thickness of plate, h=8…

Q: For the clevis connection shown, the shear stress in the 0.287-in.-diameter bolt must be limited to…

A: Bolt diameter, d=0.287 inShear stress, τ=29 ksi

Q: Two solid cylindrical rods support a load of P = 25 kN as shown. Determine the 5.6 m 3.8 m O 25.63…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.