Given the assembly shown is a cylinder rod position vertically and is supported by a collar and a bearing plate. What will be the maximum axial load P in N that can be applied to the cylinder rod considering that the average punching shear stress in the collar and the allowable bearing stress between the collar and the plate will not exceed 70 and 100 MPa.

Given the assembly shown is a cylinder rod position vertically and is supported by a collar and a bearing plate. What will be the maximum axial load P in N that can be applied to the cylinder rod considering that the average punching shear stress in the collar and the allowable bearing stress between the collar and the plate will not exceed 70 and 100 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ı need solution
A simplified model of a basketball hoop is shown. During a basket dunk a player hangs from the rim applying a force of 320 lbs including a dynamic load factor. The stand is a square tube with 5 inches outside length and 0.25 inches thickness. The distance from the edge of the rim to the middle of the square tube is 4 ft. Assuming the model is rigid, the normal stress at point A is most closely equal to: A 36 psi 1284 psi 1248 psi 1212 psi
please answer all with a completee solution, thank you
PLEASE ANSWER NUMBER 1.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
please answer number 3.Mech 222- mechanics of deformable bodies:please give detailed solutions and correct answers.i will report to bartleby those tutors who will give incorrect answers.
i need the answer quickly
Two cable support a block of weight W as shown, given the cross-sectional area for AB as 650 mm? and for AC as 475 mm2. Calculate the maximum safe load of W if the stress is limited for 100 MPa for the both cable. 60 40 W
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 189 MPa, determine the minimum diameter required for each rod. Assume P = 70 kN and Q = 118 kN. d2 di B Answers: d1 = i mm. d2 = i mm.
II. A post tapers uniformly from a diameter d at the upper end to a larger diameter D at the lower end, as shown. It supports an axial load of P. Given allowable stress of S, the post's dimension can be determined using the formula o=P/A. For structural safety, what must be the area in this formula? The lower, middle, or upper cross- section of the post? Why? Upper Area Middle Area Lower Area
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. For the connection shown, the average shear stress in the 13-mm-diameter bolts must be limited to 270 MPa. Determine the maximum load P that may be applied to the connection. O 271 KN O 215 kN O 232 KN O 291 KN O 173 kN
The figure shows a flat hanger bar for supporting shop equipment in a factory. The bar is fixed to a support by means of a bolted connection. The main part of the hanging bar is 1.5 inches wide. This width varies up to 3.0 inches. A 1.0-inch diameter bolt transfers the hanger bar load to the two top bracket plates. Determine the allowable stress of the tension load P in the hanger in the following two instances: to. The allowable tensile stress in the main part of the hanger is 16,000 psi. b. The allowable stress load between the hanger bar and the bolt is 26,000 lb/pu.
(4) The plunger of an oil pump is held against the operating cam by a spring made of No.10 W&M gage steel wire coiled with an outside diameter of ⅞-in. There are five active coils. The open length is 1.1875in. What are the length & stress when a load of 30lb is applied.