The lap joint shown if Fig. is fastened by four 3/4 inch diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 16 ksi and the bearing stress in the plates is limited to 20 ksi. Assume the applied load is uniformly distributed among the four rivetd 4 in 7/8 in P = 28.3 kips O P = 24.74 kips O P = 20.5 kips O P = 15.4 kips O a 7/8 in

The lap joint shown if Fig. is fastened by four 3/4 inch diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 16 ksi and the bearing stress in the plates is limited to 20 ksi. Assume the applied load is uniformly distributed among the four rivetd 4 in 7/8 in P = 28.3 kips O P = 24.74 kips O P = 20.5 kips O P = 15.4 kips O a 7/8 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer it correctly please and explain your answer. I will rate accordingly.
hints: The ﬂask will be filled with water (at a constant rate of 500 gallons per minute). It will take me exactly 10 minutes to escape from the chains. The diameter of the tank at 1 foot intervals. I am 5 feet 9 inches tall, and I'm pretty skinny so that you can ignore both my volume and the volume of the stool in your analysis. A gallon is equal to 0.13368 cubic feet. You can think of the volume and the height of the water as functions of time. You can easily find an expression for V (t), and then use your expression for volume in terms of height to solve for h(t). after 10 minutes amount of water in the tank=66.84 ft3 t=69.3 minutes h(t)=e66.84t/100pi -1 h(10)=e66.84(10)/100pi -1=7.39 ft Height of stool=1.64 ft Height of water in the tank=7.39 ft Questions: show work How fast is the water rising? I would like to know how long I will have to hold my breath during the last part of the stunt.
Please and explain step by step, instructions given at top
LESSON: AUTODESK FUSION 360 Choose from the choices below:
Hello. Would it be possible to get a more detailed solution? Thank you
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
6. Please help me solve this mech. engineering question
continue others
1. “The grain size of metal sheet influences its formability in two opposing ways. The yield strength of a metal increases as the grain size decreases. So, the formability of a component may decrease if the grain size gets too small. Larger grained metals have better formability, but the roughened surface that results from stretching metal with grain sizes that are too large is unacceptable for many applications. During a recrystallization anneal new grains form in the metal. The final grain size depends on the annealing temperature and annealing time.” As shown in the figure below (1"x1" area under a 50Xmagnification microscope), a cold-rolled metal has been annealed at 550 degrees C for one hour. Calculate the ASTM Grain Size Number for the following condition: image attached
i need the answer quickly