The beam has a rectangular cross section and is subjected to the loading shown. Determine the state of stress at point B. Take F₁ = 390 lb. F₂ = 540 lb (Figure 1) Figure F₂ 2 in. 2 ip 10 in. 1.5 in. 1.5 in. B 41 in. 1 of 1 > ♥ ▼ Part A Find o Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in case of tension. 4 0₂ = Submit Part B μА Value G Request Answer €350 a C Units FIG Find a Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in case of tension. A A a O 2 ?

The beam has a rectangular cross section and is subjected to the loading shown. Determine the state of stress at point B. Take F₁ = 390 lb. F₂ = 540 lb (Figure 1) Figure F₂ 2 in. 2 ip 10 in. 1.5 in. 1.5 in. B 41 in. 1 of 1 > ♥ ▼ Part A Find o Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in case of tension. 4 0₂ = Submit Part B μА Value G Request Answer €350 a C Units FIG Find a Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in case of tension. A A a O 2 ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows the cross section of a circular steel tube that is filled with concrete with a rigid cap. Calculate the stress in the concrete caused by the 200 kip axial load. Use Es = 29 x 10° psi and Ec = 3.5 x 10° psi. Express your final answer in psi and use two decimal places. 200 kips Steel 6.5 in. Concrete 6 in
SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer for Part A and Part B with Thank you Express your answer to three significant figures
(1) Given: B P=28 KN Square Bars b₁ = 57 mm (2) Q =9 kN b₂ C b₂ = 19mm (3) Q R = 38 kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
Part A 100 mm 100mm 150 mm 4 150 mm BM Determine the bending stress developed at corner A. Take M = 46 kN m (Figure 1) Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension.
Remake the diagram for this problem. Empasize the area of 1,2,3, 4 and refer to the solution. No need to solve. Just the diagram
Qs 2. A cylindrical tool steel specimen that is 152.4 mm long and 6.35 mm in diameter as shown Figure 1 rotates as a cantilever beam. It is designed so that failure never occurs. Assuming that the maximum tensile and compressive stresses are equal, evaluate the maximum load that can be applied to the end of the beam.
10.Find the stresses in member BC, BD and CF for the truss shown in Figure 8. Indicate tension or compression. The cross-sectional area of each member is 1600 mm2.
The plastic block is subjected to an axial compressive force of F = 910 N. (Figure 1) The caps at the top and bottom distribute the load uniformly throughout the block. Figure 30% 50 mm 50 mm F 150 mm 50 mm 1 of 1 Part A Determine the average normal stress acting along section a-a. Express your answer to three significant figures and include appropriate units. Ja-a= Value Submit Part B Ta-a = μA Submit Request Answer Determine the average shear stress acting along section a-a. Express your answer to three significant figures and include appropriate units. LO μA Value Units Request Answer ? Units ?
The frame supports the distributed load shown with a maximum intensity of wo = 2 kN/m. Determine the state of stress acting at point E. (Figure 1) Figure Wo D• Tism+ism+ -3 m TO 3m 20 mm) 60 mm 20 mm m D E 50 mm Part A Determine the normal stress at point E. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. JE = 57.8 Submit Part B μA Previous Answers Request Answer MPa X Incorrect; Try Again; 5 attempts remaining TE=0.864 Determine the shear stress at point E. Express your answer to three significant figures and include the appropriate units. μA ? MPa Submit Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
Question 3: The state of stress at a point in an elastic body is defined by the stress components, O11 = 2000; O22 = -2000; o12 = 1000; G23 = -400; 013 = 033 = 0. A plane that passes through the point has unit normal vector (1/5, 3/5, 3/V5) in relation to the x, y, z axes. (A) Find the stress vector components of the X, y, z axes acting on the plane. (B) Find the magnitude stress vector components of the x, y, z axes acting on the plane. (C) Find the magnitude of the normal stress acting on the plane. (D) Find the magnitude shear stress acting on the plane. (E) Construct the 3D Mohr's circle. (You can use the graphical paper to construct the circle and then take photo or by scanner to attach it with your answer). (F) Based on the Mohr's circle, determine the principal stresses and the maximum shear stress.
Question 1 The couple and evenly distributed load in Figure Q1 are both applied to a simply supported steel beam with a channel-type cross section. Determine the maximum compressive and tensile stresses in the beam. 20 kN/m 3 m 10 kN-m Đ 1m 1m. Figure Q1 40 mm 225 mm 40 mm 40 mm 200 mm
1) Figure 1 shows an element with stresses. Angle 1 Tyx Txy Tyx Figure 1 Point A(-x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA a) From basic priciples determine the stresses on the plane of the indicated angle 1. (30°) Show al calculations. Draw the orientation of the stress block for this scenario.