A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of  21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length  of the cylinder if it is twice the diameter of the cylinder

Q: The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block.…

A: Given data  Diameter of rod AC = 20 mm Distributed load on AB = 4 kN/m Find the axial normal stress…

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it…

A: Given: Here is the given data, Axial force, F=53 kN Stress, σ=52 MPa dido=26 To find: The outer…

Q: The suspender rod is supported at its end by a fixed-connected circular diskas shown in Fig. 1–26a.…

A: Given : The diameter of hole, D = 40 mm The allowable normal stress = 60 MPa The allowable shear…

Q: Explain any two methods for reducing stress concentration in a machine component with the help of…

A: Stress concentration - Whenever a machine component changes the shape of its cross section, the…

Q: A steel cable of diameter in. is attached to an eyebolt and tensioned to 520 lb. Calculate the…

A: Stress is Force per unit area.

Q: The state of stress at a point is given by ox=-6 MPa, oy=4 MPa, and Txy=-8 MPa. The maximum tensile…

A: To find: The maximum tensile stress at the point. Given: The stress are σx=-6 MPa, σy=4 MPa and…

Q: Determine stress produced by tensile force of 20 N applied on cross sectional area of 5 mm2

A: Given data: Tensile force (F) = 20 N Cross sectional area (A) = 5 mm2 Need to determine the stress…

Q: The rectangular bar shown is connected to a support bracket with a 27 mm diameter pin. The width of…

A:

Q: The stresses shown on the left below act on horizontal and vertical planes through a point on the…

A: Principal stress is defined as the maximum or minimum value of normal stresses and they act on that…

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

A:

Q: solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: Given data as per questionLoad on the bar =25 kg=245.25 NLimiting stress of the bar =27.24kpawe know…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A:

Q: The rod has a diameter of 40 mm. It is subjected to the force system F₂ = 1300 N, F, = 600 N, F₂ =…

A: The rod diameter d =40 mm = 0.04mThe force systemFx= 1300NFy= 600NFz= 900NFindThe Normal stress act…

Q: y 3D The state of stress at a point is given by oxx = -93 MPa, ayy = 69 MPa, ozz = 58 MPa, oxy = 0…

A:

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: To read quetsion carefully

Q: A 20 in-diameter air compressor is operating with a maximum pressure of 24 psi. The bolts have a…

A: The given information in the problem is represented in the following attached image:

Q: Answer the following

A: Given data The initial temperature of the bar is T1=72°F The final temperature of the bar is T2=0°F…

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: P= 189.3 kN= 189.3(1000) N= 189300 N Cross sectional area of the bronze, ABronze= 400 mm^2 Magnitude…

Q: The distribution of stress in an isotropic aluminium machine component is given (in MPa) as: σ₂ = y…

A:

Q: The plastic pipe AC has a hollow circular cross- section as shown to the right. Determine the normal…

A:

Q: Solve for the minimum thickness of a pressure vessel that is designed to hold gas at a pressure…

A: Given data,  P=1385 psi.  d=2.5 ft.= 30 in.  S= 14 ksi. =14000 psi

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 650kPa. If the allowable…

A:

Q: A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v =…

A:

Q: material is 280 MPa. Using a safety factor of 1.5, determine the material thickness of the tank in…

A:

Q: A spherical pressure vessel 4 ft. in diameter with a wall thickness of 0.25 in is subjected to an…

A:

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

A: The stress in the cable is 12782.082 psi.

Q: The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.

A:

Q: 2m Z 1.5 kPa R T I'm

A:

Q: The two pistons at the ends of the cylinder gradually increase the air pressure. The circumferential…

A:

Q: hat are the main factors affecting on the impact test? And, How?

A: given:

Q: A cylindrical pressure vessel is made by shrinking a brass shell over a mild steel shell. Both…

A: Given Data The wall thickness is:hwall=6 mm The external diameter of the brass tube is:De=750 mm…

Q: m high and 5 m in diameter is to be filled with water. Find the minimum thickness of the tank…

A:

Q: A compound cylinder is made by shrinking a jacket with an outer diameter of 200 mm on a hollow…

A:

Q: A short post constructed from a hollow circular tube of aluminum supports a compressive load of P =…

A:

Q: piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º…

A:

Q: ss in the pipe is 2.50 kN/mm², calculate the minimum wall thickness required for the pipe. Give your…

A: The Inside diameter of the pipe, (di)=42 mm. The axial load on the pipe,(P)=850 kN. The allowable…

Q: The same circular plate, as in the previous questions, is considered. Assume a plate radius of…

A:

Q: A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which…

A:

Q: A metal block of cross-section area A and length L is subject to a tensile stress of S. The block…

A: