A compound cylinder is made by shrinking a jacket with an outer diameter of 200 mm on a hollow cylinder with diameter of 100 mm and 150 mm. When the compound cylinder is subjected to an internal pressure of 35MNm-2, the maximum circumferential stress in both cylinders is the same. Calculate the maximum stress developed at the internal diameter of the jacket.

Q: a. Take a cut through the section where the AB and BC segments are connected (shown in the figure at…

A: we are to determine the stress distribution  at section B, and the load at point C

Q: QUESTION 1: 1.1 A cylindrical vessel has external diameter 920 mm, length of 2.0 m and metal…

A: Given Data:   External Diameter of cylinder = D = 920 mm = 0.92 m Length of cylinder = L = 2 m…

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: For a cylindrical steel pressure vessel of inner diameter 50 in and constant wall hickness 0.125 in,…

A: Inner diameter of vessel, Di=50 in,Thickness of vessel, t=0.125 in,Pressure inside the vessel, P=200…

Q: (a) What pressure can the cylinder carry if the permissible tangential stress is psi and the theory…

A:

Q: cast aluminum cylinder of a portable hydraulic riveter is d mm in diameter. The pressure of the…

A:

Q: Calculate the tangential stress in the steel.

A: Given that ,  R=250mm  t=20mmP=4.5MN/m2  =4.5×106N/m2

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin.  The width of…

A: Given Data The diameter of pin is:d=24mm=24×10-3 m The width of the rectangular bar is:b=70…

Q: A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal…

A:

Q: For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…

A: Sddd

Q: The rod has a diameter of 40 mm. It is subjected to the force system F₂ = 1300 N, F, = 600 N, F₂ =…

A: The rod diameter d =40 mm = 0.04mThe force systemFx= 1300NFy= 600NFz= 900NFindThe Normal stress act…

Q: What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a…

A: Given data:- load =1000 Ncross-section area =20 mm 30 mmTo find:-the stress in a rectangular rod (…

Q: The steel pipe in (Eigure 1) has an inner diameter of 3.54 in, and an outer diameter of 3.79 in.…

A: To find:The principal stresses at point .Given:The outer diameter of the pipe is .The inner diameter…

Q: A link is loaded as shown, it is attached with two bolts with a diameter of and its thickness is 0.1…

A: The diameter of bolt is The width of link is The thickness of link is The normal stress on link is

Q: Determine the maximum shear stress in the shaft (Figure 1). Given the torsional shear stress is 45…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is…

A: According to the information we have a boiler with a diameter of 300 mm and a length of 1000 mm…

Q: The plastic pipe AC has a hollow circular cross- section as shown to the right. Determine the normal…

A:

Q: A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5…

A: Given, Radius of cylinder = R = 500 mm Thickness of cylinder = t = 10 mm Internal pressure = P = 5…

Q: The average circumferential stress

A: Given data;   Thin cylinder of ,Inner radius , =500 mmThickness= 10 mmInternal pressure=5 MPa We…

Q: Q6 A spherical vessel of 1.6m inner diameter is constructed by joining two hemispheres with equally…

A:

Q: A closed thin walled cylindrical vessel has a diameter D of 470 mm, a wall thickness t, and length L…

A:

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

A:

Q: he bent pipe has a 1.5-in. outer diameter and a 0.2-in. wall thickness. Calculate the largest shear…

A: Let us draw the Free body diagram

Q: wo 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm…

A:

Q: For the thin-walled pressure vessel subjected to an internal pressure of 150 psi and as shown below,…

A: The stress that acts in parallel direction with the longitudinal axis is called longitudinal stress…

Q: A cylindrical hollow tube with closed ends is pressurized to a gauge pressure of 10 MPa and twisted…

A:

Q: |P2=20kN 0.5 m A P1=100kN 40 mm 40 mm 25mm 25mm

A: Area of cross-section,A=50*80A=4000 mm2Moment of inertia about normal axis,Ix=50*80312 Ix=2133333.33…

Q: A thick cylinder has an outside diameter of 100 mm and an inside diameter of 60 mm. It is…

A:

Q: Determine the state of stress at point A on the cross section of the pipe at section a - a. Take P=…

A: Data given  P = 6.1 kN  ro = 50 mm  ri = 40 mm

Q: A pipe carrying steam at 3.0 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A…

A:

Q: For the shown element, what are the principal stresses and their orientations (ew, cew), draw the…

A: (a) To find: The principle stress and the orientation of principle stress Given: The stress in…

Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected…

A: Diameter of the cylindrical steel pressure vessel, D=400 mm=0.4 mWall thickness of cylindrical steel…

Q: The thin-walled cylinder can be supported in one of two ways as shown in the figure below. Determine…

A:

Q: The steel pipe in (Figure 1) has an inner diameter of 4.57 in. and an outer diameter of 4.82 in.…

A: To find: The principal stresses at point A. Given: The outer diameter of the pipe is do=4.82 in. The…

Q: A cylindrical pressure vessel is made by shrinking a brass shell over a mild steel shell. Both…

A: Given Data The wall thickness is:hwall=6 mm The external diameter of the brass tube is:De=750 mm…

Q: Calculate the stress in the circumferential section of boiler steam drum 2.15 m in diameter and 45…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.