ENERAL INSTRUCTIONS:Write your complete solutions legibly on clean sheets of paper.I.Solve the following problems, complete with free body diagrams, clear solutions, and completefinal answers.100 kN50 kN12|d1— 30 тmd2= 50 mm1.100 kN0.9 m1.2 mRods 1 and 2 are welded together and are subjected to the shown loads. Given themeasurements shown, determine the average normal stress internally experiencedby rods 1 and 2, and specify whether these stresses are tensile or compressive.

To determine the average normal stress in the rods 1 and 2.

Solve the following problems, complete with free body diagrams, clear solutions, and complete final answers. I 100 kN 50 kN 1 2 d1 = 30 mm 1. 100 kN d2 = 50 mm 0.9 m 1.2 m Rods 1 and 2 are welded together and are subjected to the shown loads. Given the measurements shown, determine the average normal stress internally experienced by rods 1 and 2, and specify whether these stresses are tensile or compressive.

Solve the following problems, complete with free body diagrams, clear solutions, and complete final answers. I 100 kN 50 kN 1 2 d1 = 30 mm 1. 100 kN d2 = 50 mm 0.9 m 1.2 m Rods 1 and 2 are welded together and are subjected to the shown loads. Given the measurements shown, determine the average normal stress internally experienced by rods 1 and 2, and specify whether these stresses are tensile or compressive.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The boom AC is a 4-in. square steel tube with a wall thickness of 0.30 in. The boom is supported by the 0.65-in .-diameter pin at A, and the 0.45-in .-diameter cable BC. Neglecting the weight of the boom, determine the tensile stress in the cable (in psi) if P = 4490 lb. Round off the final answer to three decimal places.
Shown is the stress-strain curve developed from the tension test of a metal alloy bar. The specimen used to develop the stress-strain curve has a round cross-section with a diameter of d = 7 mm and a gauge length of L = 370 mm. Determine the load that must be applied to the specimen to stress the specimen to it's 0.2% offset yield. Express your answer in kN to the nearest whole kN. Your written solution must also include the length of the specimen when stressed to the 0.2% offset yield stress. σ (MPa) 700 600 500 400 300 200 100 0 0.02 0.04 0.06 0.08 0.10 0.002 0.004 0.006 0.008 0.010 € (mm/mm) P d
Use 32 in2 and 48 in2 cross-sectional areas for tensile and compressive members, respectively. Determine the axial stress in member CD in psi. (Numerical absolute answer only without units in 3 decimal places)
Problem 2: Use an eigenvalue approach to solve for the principal stresses and directions for the state of stress shown below. Show the principal stresses on a properly oriented element of material. 20 mPa
The state of stress shown below is from the surface of a bar under axial and torsion loading. Calculate the principal stresses and directions (i.e, the value of the angle 0). Draw the state of stress aligned with the principal directions. 60 MPa T 9. 40 MPa 40 MPа
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
Question 6 Two identical plates of 63 mm wide and 5 mm thick is connected by a square pin with side dimension 19 mm. If a plate is subjected to a tensile force of 29 kN, determine the maximum tensile stress (MPa) developed in the plate.
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 16 MPa in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the stresses σn, σt, and the magnitude of τnt and show them on a stress element that is properly rotated with respect to the x-y element. The sketch must include the magnitude of the angle between the x and n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise).
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown. (Figure 1) Figure 1 of 1 > Part A If the wheel is subjected to a normal force of P = 3.3 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel. Express your answer to three significant figures and include the appropriate units. Tavg= Submit Provide Feedback Value A Request Answer C Units ? Next >
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m?. What will be the stress along the face AB? (Cambridge) 12.4 19.0cm A -36 cm- 1.60 cm 1.90 cm 1.60 cm
A 40mm thick steel bar that is fabricated by welding two parts together is shown below. Being concerned for the strength of the weld, you need to find the state of stress (normal stress and shear stress) in the plane of the weld for an applied load of 400kN. Draw your result on a stress element. 57° 400 kN 400 kN 100 mm