The lap joint shown is fastened by four 3/4-in.-diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 14 ksi and the bearing stress in the plates is limited to 18 ksi. Assume the applied load is uniformly distributed among the four rivets. P P 4 in 7/8 in 7/8 in P

The lap joint shown is fastened by four 3/4-in.-diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 14 ksi and the bearing stress in the plates is limited to 18 ksi. Assume the applied load is uniformly distributed among the four rivets. P P 4 in 7/8 in 7/8 in P

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.6.6P

See similar textbooks

Similar questions

Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
I need the answer as soon as possible
Also need to show FBD
I NEED ANSWER
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa
W/FBD
The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120KN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel to be used, the maximum allowable stresses are: o = 180 MPa, t = 120 MPa, op = 380 MPa. Design the tie bar by determining the required values of: a. the diameter d of the bolt, b. the dimension b at each end of the bar, c. the dimension h of the bar.
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
9 Determine the shearing stress, In MPa, on the fiber 30mm above NA at distance 1m from A 10 Determine the spacing, in mm, of rivets on the steel plate
A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. o a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN Pe
3. A threaded rod and nut arrangement are guided with two washers, upper and lower washers tightened into a base plate. Considering that the base plate carries a load of 120 kN including its self-weight which is distributed equally: a. Determine the stress on the lower washers before the buts are tightened. b. Determine the stress int the upper washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. Determine the stress int the lower washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. c. 44 mm Upper washer Base plate Lower washer 20 mm 22 mm 50 mm