5.6-2 A fiberglass bracket ABCD of solid circular cross section has the shape and dimensions shown in the figure. A vertical load P = 40 N acts at the free end D. (a) Determine the minimum permissible diameter dmin of the bracket if the allowable bending stress in the mate- rial is 30 MPa and b = 37 mm. (Note: Disregard the weight of the bracket itself.) (b) If d = 10 mm, b = 37 mm, and allow 30 MPa, what is the maximum value of load P if vertical load P at D is replaced with horizontal loads P at B and D (see figure part b)? 6b (a) 6b (b) D P -2b -2b B C 'T'

5.6-2 A fiberglass bracket ABCD of solid circular cross section has the shape and dimensions shown in the figure. A vertical load P = 40 N acts at the free end D. (a) Determine the minimum permissible diameter dmin of the bracket if the allowable bending stress in the mate- rial is 30 MPa and b = 37 mm. (Note: Disregard the weight of the bracket itself.) (b) If d = 10 mm, b = 37 mm, and allow 30 MPa, what is the maximum value of load P if vertical load P at D is replaced with horizontal loads P at B and D (see figure part b)? 6b (a) 6b (b) D P -2b -2b B C 'T'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The horizontal bar ABC is supported by a pin at A and two rods with identical cross- sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 80 kN is applied. Use Est = 200 GPa and Eal = 70 GPa. %3D Steel Aluminum A B T2 m- 1.5 m- Im
Assume that the truss is simply supported at joints M and E. Determine the stress at member AH if P.= 15.375 Kips, the area is 11 in. Answer your problem with the given unit ksi. Pu Pu P. Pu P. P. P. * a w - LKJ IH G
A steel column is pin connected at the top and bottom which is laterally braced and subjected to transverse loading. It carries an axial load of 800 kN and a 70 kN-m moment. Use ASD. The steel section has the following properties: A = 13000 mm² r = 94 mm Ix = 300 x 106 mm4 Sx = 1200 x 103 mm³ L = 3.6 m Yield stress Fy = 248 MPa Axial compressive stress that would be permitted if axial force alone existed, Fa = 115 MPa Compressive bending stress that would be permitted if bending moment alone existed, Fb = 148 MPa Members subjected to both axial compression and bending stresses shall be proportioned to satisfy the following requirements: Mry + 9 Mex Mey Determine the axial compressive stress if axial load only existed. Pr 8 Mrx + Pe 75.82 MPa 61.54 MPa 33.96 MPa 16.25 MPa Determine the bending stress if bending moment alone existed. 76.25 MPa O58.33 MPa 13.33 MPa ≤ 1.0 16.59 MPa Determine the value of both axial and bending moment interaction value, considering the amplification due to…
For the given properties of beam below. Design the reinforcements of the beam. d'=75 mm b=400 mm d=580 mm fc'=35 MPa fy=320 MPa Mu=1000000000N mm Input is 0 in As' if compression bars are not needed. A. USE NSCP 2001, As = mm2, As' = mm2 B. USE NSCP 2015, As = mm2, As' = mm2 %3D
PLEASe answer this question. Thank you
Consider the singly reinforced beam section given below (left figure). The stress block parameters for the cross-section from IS: 456: 2000 are also given below (right figure). The moment of resistance for the given section by the limit state method is kN-m. 300 mm M25 4-120 Fe415 200 mm 0.42x 0.36 um = 0.48d for Fe415
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
Read the question carefully and give me all right solutions with clear calculations.
The beam is subjected to a loading condition as shown in th figure. Determine the (a) maximum tensile stress and (b) maximum compressive stress with the givenm cross section. Show you complete solution and diagram.
Determine the stress in each member of the truss shown. Get first the value of RAv then Find the value of member AE @ Joint A