3. For the given structure and boundary conditions, what is the allowable load Pallow if the material strengths in shear and tension are t = 200 MPa and o=360 MPa, respectively? The pins carry shear and bars BC and DE carry axial load. Disregard the stress conditions of member ACD, which carries lateral load. All pins are in single-shear and have a diameter of 12mm. Use a factor of safety of 2.0. A ABC = 100mm2 B D C Pallow E ADE = 100mm2 240mm 150mm

3. For the given structure and boundary conditions, what is the allowable load Pallow if the material strengths in shear and tension are t = 200 MPa and o=360 MPa, respectively? The pins carry shear and bars BC and DE carry axial load. Disregard the stress conditions of member ACD, which carries lateral load. All pins are in single-shear and have a diameter of 12mm. Use a factor of safety of 2.0. A ABC = 100mm2 B D C Pallow E ADE = 100mm2 240mm 150mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Maxinam allowable stress for steel -140 MPa Maxinnum allowable stress for ahıminuum = 90 MPa Maxinun…

A: Given:- Maximum allowable stress for steel = 140 MPa Maximum allowable stress for aluminum = 90 MPa…

Q: 22) One brass bar and one steel bar are forming the setup shown below. Determine the tresses and the…

Q: A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that…

A: Given:- L = 1.0 m, A = 3000mm2, modulus of elasticity E = 45 GPa, gap s = 1.0 mm. To find:- (a)…

Q: Ҫар 10 3. The force on the chain in the system shown F = 500 N Find the average tensile stress on…

A: It is required to determine the average tensile stress on the chain. σ=FAc Here F is the force, and…

Q: A tie-down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the…

A: Given:

Q: a) Calculate the internal forces/moments at point J? b) Bar DE is made of aluminum with Young…

Q: DETERMINE THE LARGEST LOADP THAT CAN BE APPLIED TO THE BARS OF THE LAP JOINT SHOWN IN THE FIGURE.…

Q: Determine the maximum permissible value of T provided the allowable shearing stresses in brass and…

A: ζb=70 MPaζs=110 MPaGb=80 GPaGs=40 GPa di=70 mmd0=90 mm

Q: 0,3in 0.4in2 3P 2P + C. Find the albwable säfe p if the stresses in the bar are the following: AB 50…

Q: 2. The following the truss figure, came from your Module 1. Page 9. 3 m H H C G 30 kN 70 kN 4 panels…

Q: Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all…

Q: Bar FA in the pin-connected structure below is to be considered rigid and is horizontal before loads…

A: Given that : Properties of member BC : E = 75 GPa Cross sectional area = 1000 mm2 Properties of…

Q: the seven bolts connection in the figure below, the diameter of the bolt is D= 1 in, the width of…

Q: A Steel A = 480 mm? 1.0 m 3P Bronze A = 650 mm? 2 m C 2P

A: The given data is: Length of rod AB = 1 m Length of rod BC = 2 m Area of rod AB = 480 mm2 Area of…

Q: The three suspender bars AD, BE, and CF are made of the same material (E = 70 GPa) and have equal…

A: Given Data Three suspender bars are givenCross-sectional area A=450 mm2Young's modulus E=70 GPaTwo…

Q: Consider the given figure. The bar AC is 6 mm thick and is made of a steel with a 425 MPa ultimate…

A: Given:- The thickness of the bar AC (t) = 6 mm The ultimate stress of the steel = 425 MPa The…

Q: 1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

Q: One1 the are two For thickness Subjected ponts Subjected aN/m. is the retanglugar plate all…

A: To find - Equilibrium equation of the structure.

Q: Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum…

Q: The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of…

Q: .2 ft, and LcD = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. P Į B…

Q: When the normal stresses are at their maximum or minimum values, the shear stresses are zero. We can…

A: 1- Yes when normal stresses are maximum or minimum, then at that element shear stress is zero. 2-…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

Q: 1 1 Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing…

A: A square section of dimension in2 is bent into two sectionsSquare sectionDiamond sectionThe…

Q: The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear…

A: Given data in question Load 750 kN Diameter 32 mm To find out Permenant strain

Q: Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter…

Q: A small aluminum alloy [E = 76 GPa] tee shape is used as a simply supported beam as shown. For this…

Q: Problem 01.054- Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is…

Q: : Determine the appropriate weigh

Q: A gusset plate is connected to the flange of column with the help of fillet weld on both sides as…

Q: The bending stress distribution for the given beam at the bottom fibre are of in nature. w kN/m A B…

A: The given loading is continous and acting vertically downwards.

Question

3. For the given structure and boundary conditions, what is the allowable load Pallow
if the material strengths in shear and tension are T = 200 MPa and o=360 MPa,
respectively? The pins carry shear and bars BC and DE carry axial load. Disregard the stress
conditions of member ACD, which carries lateral load. All pins are in single-shear and have
a diameter of 12mm. Use a factor of safety of 2.0.
A
ABC = 100mm2
B
D
C
Pallow
E
ADE = 100mm²
240mm
150mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. In this case; a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamp material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPA, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D %3D (Please solve in detail and according to engineering rules.) Material mechanics Sectional view a-a - 20mm T. 183mm 40mm
The aluminum rod AB (Gal = 27 GPa) is bonded to %3D the brass rod BD (Gpr = 39 GPa). The portion CD of %3D the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. 60 mm 2T 36 mm T 250 mm 375 mm 400 mm
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPa, f, = 280 MPa and the net tensile strain is greater than 0.005, then the maximum steel ratio equal............ (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
6
Please answer the question correctly and pleaase put the answer on the paper. Thank you Note: The tolerance is ± 1 in the third significant digit. Put the exact answer
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
I will rate immediately
Determine (d) variable stress and (e) design factor
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >