A truss is loaded as shown in the figure. The cross-sectional area of each member is 500 mm^2. Hint:Use method of section in getting the axial forces.Use the guide cutting sections.L-6 m+6m- N25 kN8 m50 kN -a 8 m50 kN8 m50 kN8 mB.9. Find the axial stress in member HKO 35.34 MPaO 31.12 MPaO 33.34 MPaO 37.12 MPaQuestion 1010. Find the axial stress in member HJ.O 125 MPaО 123 МPаO 127 MPaO 129 MPa

Answered: Image /qna-images/answer/2d3c358f-4e02-4f66-8e41-2c440a50eeb4.jpg

A truss is loaded as shown in the figure. The cross- sectional area of each member is 500 mm^2. Hint: Use method of section in getting the axial forces. Use the guide cutting sections. L-6m+6m- N 25 kN 8 m K 50 kN 9. a 8 m H. 50 kN 8 m 50 kN 8 m 9. Find the axial stress in member HK

A truss is loaded as shown in the figure. The cross- sectional area of each member is 500 mm^2. Hint: Use method of section in getting the axial forces. Use the guide cutting sections. L-6m+6m- N 25 kN 8 m K 50 kN 9. a 8 m H. 50 kN 8 m 50 kN 8 m 9. Find the axial stress in member HK

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The steel truss (E =200 GPa) shown in figure below has a cross-sectional area of 1920 mm². Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6 mm and a factor of safety of 2.5. b. The displacement of support D due to the load calculated in part a. 5m 6m A C F
Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 kN 120 kN B. 3 m E 200 kN 4 Panels @ 4 m = 16 m
Hand written and clean writing please
anwser 2nd part
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
The assembly shown below is pinned at A & C and A & C are subjected to a double shear. Let each pin diameter be 18 mm, and P = 20 kN. Find the:a) Force at the rod BC (kN) and force acting on pin A (kN)b) Average shear stress at A (MPa), and average shear stress at C (MPa)
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P
A rigid ban AB and "CD" as shown are supported by pins at "A" & "C" and two ross. Determine the maximum force 'p' that can be applied as given if it's vertical movement is limited to 5 mm. Neglect the weight of all the members. www A 3m 3m Aluminium P L = 2m, A= 500m² E =70 GPA 3m IB 3m Steel L=2m A= 300m² E = 2006/ D
A built up I-section is formed from plates welded together as shown in the figure. It is to be used as a column L = 3.7 m long. All elements are A36 steel and connected such the section is fully effective. Using the following properties, calculate the flexural buckling stress, Fcr, in MPa using theoretical k. Flanges: b = 150 mm, tf = 12 mm Web: h = 310 mm, tw = 6 mm Write your final answer in two decimal places only.
Need answer ASAP complete solution please
Calculate the rod forces FH, EH, and EG of the truss system for the given loading condition using the section method. State whether the rod forces are tensile or compressive.
Present your solution and box your final answer