Two 10-mm thick plate members are to be connected using straps of the samethickness and 12-mm diameter rivets as shown in the figure. Determine the maximumbearing stress if the maximum tensile stress on the plate members due to load "P' is24 MPa. The members are 50-mm wide. Assuming all the rivets fill the holes.Strap PlateMember PlateP.P

Answered: Image /qna-images/answer/be9ab567-2f0d-41d6-ae58-6d0c1a740221.jpg

Answered: Two 10-mm thick plate members are to be…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
The gusset is riveted to a larger plate by 4 – 22mm rivets in single shear arranged andloaded as shown. Calculate the stress in the most heavily loaded rivet.
A plate with width of 300 millimeters and thickness of 20 milimeters is to be connected to two plates of the same width with half the thickness by 25 millimeters by 25 millimeters diameter rivets. The rivets holes have a diameter 2 millimeters larger than the rivetdiameter. The plate is A36 with yield strength F, = 248MP.. Allowable tensile stress on net area is 0.6Fy and allowable bearing stress of 1.3Fy. The rivets are A502, Grade 2, hot-driven rivets with allowable shear stress of 150MPA. 1. Detemine the maximum load that can be applied to the connection with consideration to the yielding failure in the plates. 2. Detemine the maximum load that can be applied to the connection with consideration to the fracture failure in the plates. 3. Detemine the maximum load that can be applied to the connection without exceeding the allowable shearing stress in the rivets. 4. Detemine the maximum load that can be applied to the connection without exceeding the allowable bearing stress between…
A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
Please show its detailed solution, explanation, FBD, and units. Thank you!
In the assembly of the bronze tube and steel bolt, the pitch of the threads is p = 1/32 in.; the cross-sectional area of the bronze tube is 1.5 in? and of steel bolt is 4 in?. the nut is turned until there is a compressive stress of 4,000 psi in the bronze tube. Find the stresses (psi) if the nut is given one additional turn. How many turns of the nut will reduce these stresses to zero? Use Epr = 12 x 106 psi and E = 29 x 10° psi. L= 40 in.
A pin is used to transmit the force from the middle plate to the two plates at the top and bottom as shown. Determine the different kinds of stresses acting on the plate and the bolt in the process of transmitting this force. The thickness of each of the plates is 0.5 inches.a) Stress in the plate at a section away from the homeb) Stress in the plate at a section taken at the center of holec) Shear Stress in the boltd) Bearing stress on the top platee) Bearing stress on the middle plate
From the figure below, determine member BD.
Complete solution with free body diagram
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F
The five-bolt connection must support an applied load of P = 149 kips. If the average shear stress in the bolts must be limited to 50 ksi, what is the minimum bolt diameter that may be used for this connection? P Answer: d = i in.
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS