For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.   Please explain the solution

Q: A tie-down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the…

A: Given:

Q: A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid…

A: Given, Es=210 GPadr=12 mm4αs=12×10-6/°Cdp=15 mτ=45 MPaσ=70MPa

Q: A Sandwich block is comprised of brass in the centre with two aluminium plates attached to either…

A:

Q: The belt shown has a width of 43 mm and a thickness of 6 mm. [P1= 30 kN, P2= 6 kN, P3= 14 kN, P4= 14…

A: the width of the belt (b)=43 mm,  thickness (t)=6 mm.P1=30 kN, P2=6 kN, P3=14 kN, P4=14 kN.…

Q: The stress field in a loaded aluminum plate was determined as [-2x² + 3y² 3x + y+ 5] O = F[3x + y+5…

A:

Q: .B + sodb 30 lb CROSS. SECTION

A: Normal stress: it is defined as the stress that is induced when the member is loaded by axial force.…

Q: The plates in the figure below are each 3 inches by 0.5 inches in cross section. If the hole in each…

A: Solution:- Given information: Cross section of plate =3×0.5 in Hole diameter, d=1316 in, and Load,…

Q: A 3m-long, thin-walled section (thickness t = 4 mm, for all elements) is used as a cantilever to…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: THE PLATE SHOWN IN THE FIGURE IS FASTENED TO THE FIXED ΜΕMBER BY FIVE 10- MM- DIAΜΕ TER RIVETS.…

A:

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The…

A: Average shear stress = VA a. Find Shear force in one bolt ; V = 13 * P2 P = 6 k So, V = 1 k b. Find…

Q: When the normal stresses are at their maximum or minimum values, the shear stresses are zero. We can…

A: 1- Yes when normal stresses are maximum or minimum, then at that element shear stress is zero. 2-…

Q: Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of…

A: Length of bronze and steel rod is same.The change in length of steel is equal to the change in…

Q: The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear…

A: Given data in question Load 750 kN Diameter 32 mm To find out  Permenant strain

Q: 12 ID 12 Draw the Mohr's circle. Find the stresses on the plane shown. Fill in the blanks and table.…

A:

Q: . For the riveted connection shown in the figure using  elastic analysis a. Determine the safe value…

A: Diameter of rivet = 25 mmAllowable shear stress = 150 MPaloading = 50 KNOther Data are given in the…

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.