Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm diameter rivets as shown in the figure. Determine the average shear stress in the rivets if the maximum tensile stress on the plate members due to load "P" is 24 MPa. The members are 50-mm wide. Assuming all the rivets fill the holes. Strap Plate Member Plate |P → P

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d= 0.625 in., and each side…

A: - Horizontal axis = 0- Vertical axis = 0- Resultant force on pin is given by PR ;

Q: Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe

A: take stresses in Rod and Pipe as Equal Take sum of forces as 8KN Take moment about rod as 0

Q: A bar of a uniform cross-section is rigidly fixed at one end and loaded by an off-centre tensile…

A: Given h=18mm b=37 mm σ=234MpaF = 1.5 KN Since you have posted a question with multiple sub-parts, we…

Q: 24. A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A:

Q: A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid…

A: Given, Es=210 GPadr=12 mm4αs=12×10-6/°Cdp=15 mτ=45 MPaσ=70MPa

Q: maximum value for the load R.

A:

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 2 m 1m 25KN The thickness…

A:

Q: -150 mm B - 300 mm 30°

A:

Q: q1=150 Mpa, q2=40 MPa Calculate the stresses σx,σy,σz and deformation εz1,εz2 in the z direction.

A: Elastik cisim 1 q1=150 Mpa, σz = -150 Mpaσx,σy = 0∈z = σzE       = 150300×103∈z =5×10-4∈x =∈y =…

Q: The state of stress at a point Q is Ox = 100 MPa, o, = 20 MPa, oz = -40 MPa, Txy = 0 MPa, Tyz = 40…

A:

Q: E, 45° 45°

A: Calculate the strain in x-direction:…

Q: The rod ABCD is made of an aluminum for which E= 70 GPa. Take P = 80 kN. NOTE: This is a multi-part…

A:

Q: A 200 kN force is applied at the free end of the cantilever beam as shown in the figure below. What…

A:

Q: Question 6 of 15 The plate of thickness, t = 5 mm, is loaded with the following stress; o, =100 MPa,…

A:

Q: Determine the stress in rod if tensile force applied of 35 N having cross sectional area of 50 mm2

A: Given  Tensile force F= 35 N Crossectional area A= 50 mm2

Q: Problem (1) Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a…

A:

Q: A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which…

A:

Q: ABD rigid bar with 40mm diameter BC bar at point B, It is supported from point A with a 30 mm…

A:

Q: Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice…

A: Consider the figure,

Q: 9. Determine the cracking moment for the beam section shown. The bars are each 32mm in diameter. Use…

A: fc = 21 MPa

Q: The bent steel bar shown in Figure normal stresses at A and B. is 200 mm square. Determine the 150…

A: Given : This is a solid mechanics problem where we are asked to find the normal stresses at A and B…

Q: The state of stress at a point in a structural member may be represented by a two-dimensional stress…

A:

Q: rigid support @ A A 400 N-m 850 N-m L=1.4 m 30 mm diameter L=2.4 m 50 mm diameter L=1.9 m 30 mm…

A:

Q: Q. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: Note:- as per our company guidelines we are supposed to answer only first part. Kindly repost other…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: Determine the largest torque Tmax that can be applied at the upper end of the steel rod.

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.250 in., and each side…

A:

Q: bronze rod. Axial loads are indicated. Find the maxim exceed a stress of 80MPa Mpa in bronze. -1.0m…

A:

Q: An aluminum [E = 11100 ksi] control rod with a circular cross section must not stretch more than…

A: Given data,  Stress = 10.8 ksi E = 11100 ksi P = 2090 lb

Q: Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

A:

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: n the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B…

A:

Q: 02: For the stresses at the point shown, find: • The maximum shearing stress. • The principal…

A: