The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 45846-Nload, using the following data: length of steel = 11 m, length of bronze = 2.3 m Area of steel = 562 mm, Area of bronze = 335 mm Modulus of elasticity of steel = 195 Gpa, Modulus of elasticity of bronze = 80 Gpa x= 0.55 m, y = 1.12 m, and z = 0.78 m. Round off the final answer to two decimal places. ... Bronze Steel

The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 45846-Nload, using the following data: length of steel = 11 m, length of bronze = 2.3 m Area of steel = 562 mm, Area of bronze = 335 mm Modulus of elasticity of steel = 195 Gpa, Modulus of elasticity of bronze = 80 Gpa x= 0.55 m, y = 1.12 m, and z = 0.78 m. Round off the final answer to two decimal places. ... Bronze Steel

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES. PS: THE TOLERANCE IS 1 IN THE 3RD SIGNIFICANT DIGIT
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.29 mm the values of elastic modulus for steel is 217 MPa. Take H1 = 4 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 7 x 7 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.66 mm the values of elastic modulus for steel is 207 MPa. Take H1 = 4 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 7 x 7 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = (in N) ii) Stress-induced in the top bar = (in N/mm^2) iii) Stress-induced in the bottom bar = (in N/mm^2)
why is the external load not shown in the free body diagram of limk 2 and 4?
please answer all with a completee solution, thank you
2-1. A standard steel specimen of in. dia- meter elongated 0.0087 in. in an 8 in. gage length when it was subjected to a tensile force of 6,250 lb. If the specimen was known to be in the elastic range, what is the elastic modulus of the steel? Ans: 29.3 x 106 psi.
Q2/B Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and parallel to the column axis. If concrete has (E) of 15GPa and tensile strength of 2.8 MPa and the steel rods has (E) of (210) GPa and tensile strength of(400) GPa Determine the modulus of elasticity and tensile strength of composite if the steel rods occupy 10% of cross-sectional area of the column 021 21
Please try to solve in 30 minute
PROBLEM 4. The rigid bar is supported by a pin at A and two metal wires, each having a diameter of 4 mm. The stress-strain diagram of the steel is given in the Figure below. The lower graph is the zoomed view of the elastic deformation and yielding phases of the stress-strain diagram given by the upper graph (a) Obtain the Young's modulus of metal. What can you say about the kind of metal considering the Young modulus? If the point G is displaced 1.5 mm in vertical direction, (b) determine the forces at wires EB and DC, (b) the intensity of the distributed load w, (c) the final diameters of wires. (Poisson's ratio is v-0.3) E D o (MPa) 600 500 800 mm 400 300 G. 200 10 W 400 mm 250 mm- e(mm/mm) 150 mm 0.04 0.08 0.12 0.16 0.20 0.24 0.28 00005 00010.0015 Q002 00025 0,003 00035
The structure consists of two bars. Axial loads 40 kN and 10 kN are loaded as shown in Figure B. Determine: a) Global stiffness matrix b) Nodal displacement c) Stress in each bar Table 2 Steel Aluminium Brass Area 400 350 350 (mm³) E(Gpa) 200 70 83 Aluminum Brass Steel 40 kN - 10 kN L 500 mm 400 mm 300 mm
3. The bar shown below is composed of two pieces, AC and CD. The bar is attached to the wall at point A. The length L = 10 in. The cross sectional areas are: AAC = 4 in? and AcD = 2 in?. The Young's Moduli are: EAC =20 Msi and Ecd= 15 Msi Two forces are applied at points B and D: PB = 50 kips and PD = 20 kips. Determine: (a) the reaction force at A (specify –→ or +) and (b) the deflection of point D (specify → or +). (Hint for (b): Think about how many pieces you must subdivide the rod into.) Ans: RA = 30 kips (+), dp = 7.9167×10-3 in (E) A В C D Pp L 2L L
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.89 mm the values of elastic modulus for steel is 209 MPa. Take H1 = 7 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P in(N) = ii) Stress-induced in the top bar in(N/mm^2) = iii) Stress-induced in the bottom bar in(N/mm^2) =