A vertical steel bar shown in figure Q1 is subjected to a compressive load of 75 kN. If the stress in the middle portion is limited to 47 MN/m2, determine its cross-section dimensions. Find also the length of the middle and other portions if the total reduction in length of the bar is to be 0.04 mm. Assume Young's modulus for steel is 200 GN/m². E 200 mm C 75₁ kN Circular D=50 mm Square bxb Circular D=50 mm Figure Q1: Bar Loadings and Sections

A vertical steel bar shown in figure Q1 is subjected to a compressive load of 75 kN. If the stress in the middle portion is limited to 47 MN/m2, determine its cross-section dimensions. Find also the length of the middle and other portions if the total reduction in length of the bar is to be 0.04 mm. Assume Young's modulus for steel is 200 GN/m². E 200 mm C 75₁ kN Circular D=50 mm Square bxb Circular D=50 mm Figure Q1: Bar Loadings and Sections

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A cylindrical rod is fixed between two walls. The rod is composed of two materials. Section AC is made of one material (GAC = 2G) while section CD is made of a different material (GcD = G). A torque, T, is applied at point B, as shown below. Jac = JcD = J = 2 in. GẠC = 2G = 20 x 10ʻ psi T= 300 kip in. GCD = G = 10 × 106 psi A D 2L Determine the reactions at the wall, Ta, and Tp. Specify the direction for each. (Note: this is an example of a no calculator problem.) Ans: TA = 250 kip in ( Tp=50 kip in ( T Fixed Fixed to wall to wall
The rod shown in the figure has two cross-sectional areas, where the area of the larger cross-section is 6 times larger than the smaller. The rod is subjected to three point loads, P₁, P2, and P3 at points B, C, and D, respectively. You may assume that the bar deforms in a linear-elastic manner. The cross section of the small rod is equal to A = 2 in² and the modulus of elasticity is equal to E = 20,000 ksi. a) Find the support reactions at A and E, if P₁ = b) Draw the axial force diagram. c) Identify how the position of point C changes due to the applied loadings. A 12 in B P₁ 11 in C 10 kips, P₂ = 20 kips and P3 = 40 kips. P₂ 11 in D P3 E the axu 12 in
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.1 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 6 mm. Consider a linear elastic behavior. Select one: P = 597 N P = 537 N P = 430 N P = 573 N P = 287 N
Calculate Strain energy for truss DF. Enter your answer in J to 2 decimal places.
The cross sections of two hollow bars made of the same material are concentric circles as shown in the figure. It is given that r3 > rland r4 > r2, and that the areas of the cross-sections are the same. J1 and J2 are the torsional rigidities of the bars on the left and right, respectively. The ratio J2/J1 is r3 r2
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph The data for Pr, Pñ, atand eare-shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 5. KN 30omm a Gomm Ph 14mm 120 mm L = 2400mm Figure 1 250 mm
The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross- sectional area of the wire is 1.75 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. D 90 cm 90 cm B 180 cm Ale 120 cm
Problem 3: (M4) Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square steel column (E=200 GPA) that can withstand an axial compressive load of 50 MN, the outer dimension a is 400 mm. The column's cross section is shown in Figure.4. Assume the column is a fixed-free type. b Figure.4: Cross-section of a hollow-square steel column
Problem 3: (MМ4) Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square steel column (E=200 GPA) that can withstand an axial compressive load of 50 MN, the outer dimension a is 400 mm. The column's cross section is shown in Figure.4. Assume the column is a fixed-free type. a b Figure.4: Cross-section of a hollow-square steel column
What is the advantage of nitriding? Select all correct answers. Some complex components can be nitride without difficulty. Better wear resistance. Better fatigue resistance. The cheapest method of case hardening. What is the correct definition of plastic deformation? The behavior of a material when its size changes by the addition of heat. The behavior of a material that deforms under load and returns to its original shape when the load is removed. Deformation caused by cleavage, where the material is actually pulled apart across atomic planes within the crystals or along the grain boundaries. The behavior of a material that deforms under load and does not fully return to its original shape when the load is removed.
( 48ll O O 2 9:YV The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: A B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
Problem 3 The steel rod shown in the figure is stress- free before the axial loads P1 = 150 kN and P2 = 90 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial stress in each segment after the loads are applied. Use E = 200 GPa A A = 900 mm² 500 mm A = 2000 mm² B P₂ A = 1200 mm² с -250 mm 350 mm D